aluminium plate中文,aluminium plate的意思,aluminium plate翻译及用法

2026-05-05 13:41 浏览次数 16

aluminium plate

英[ˌælju:-ˈminjəm pleit]美[ˌæljəˈmɪniəm plet]

铝板;厚铝板

aluminium plate 片语

片语

aluminium compound plate铝复合板

aluminum plate铝板

aluminium printing plate铝版印刷

aluminium compound plate curtain铝复合板幕墻

aluminium plastic plate铝塑板

planar aluminium quadrate plate平面铝方板

aluminium litho plate胶印铝版

flat aluminium alloy plate铝合金平板

aluminium m plate evaporator铝平板蒸发器

aluminium mold plate铝膜板

aluminium plate 例句

英汉例句

  • The reasons for the existence of diagonal deviation on aluminium plate after it is trimmed by 1500 cut-to-length line is analyzed in this paper.

    分析了1500横切机生产切边铝板时铝板对角线存在偏差的原因,提出了切边铝板对角线偏差控制途径,表明切边铝板对角线超差废品可控制在极小的范围。

  • The corrosion protection layer arranged on the surface of the back face aluminium plate enhances the corrosion protection effect of the compound plate, thereby prolonging the service life.

    在背面铝板表面设置有防腐层,增强其防腐效果,延长使用寿命。

  • The corrosion protection layer arranged on the surface of the back face aluminium plate enhances the corrosion protection effect of the utility model, thereby prolonging the service life.

    背面铝板表面设置有防腐层,增强其防腐效果,延长使用寿命。

  • This article discussed anodic oxidation mechanism of aluminium plate by means of electrode potential, Nernst equation, overpotential and so on.

    用电极电势、能斯特方程式和超电势等,论述了铝板的阳极氧化机理。

  • A new process of manufacturing decorative aluminium plate is introduced. The figures were engraved by a newly developed mixed acid.

    提出了采用耐酸油墨丝网印刷所需图案、混合酸刻蚀制备装饰性铝板的新方法。

  • The dynamic stress inside green sand during experimental compaction by air impact moulding can be achieved using a method of placing aluminium plate at the top of green sand.

    采用气沖造型机并在型砂顶部覆盖铝板的方法,获得了气力沖击造型试验紧实过程中型砂内部的动态应力。

  • The concave-convex hammering lines formed on the surface of the front side aluminium plate are strong in stereo dimension, and elegant and beautiful in appearance.

    在正面铝板表面设置有凹凸的锤印纹,立体感强,高雅大方,外表美观;

  • The effects on anodization coloring of coloring of commercial aluminium plate are discussed from grain size, composition, gases and dregs of cast-rolling plate.

    论述了铸轧板晶粒度、化学成分、气体、夹渣含量对工业纯铝板着色性能的影响,提出了改善铸轧板质量进而减小着色色差的方法。

  • The printing and coating process on tin plate and aluminium plate cans were described.

    简述了马口铁罐和铝质罐的印刷涂装工艺。

  • Thickness of the aluminium plate is measured with laser ultrasounds. It tallies quite well with the real value. The minimum displacement which can be detected by the system is also meas...

    用激光超声测得铝块厚度与实际值很好地吻合,同时测出了系统的最小可探测位移。

  • This is similar to another aluminium plate system shown below which is nearing completion at USL and is destined for a customer in China.

    该系统与另一个铝板系统相似,该系统显示在下面,且已在USL接近完成,最终客户在中国。

  • He ignored distinctions of race or caste, and was happy to eat rice from an aluminium plate in the house of an untouchable.

    他不理睬种族与种姓的差异,他曾经在一个贱民的家里很高兴地从铝盘子里取米饭来吃。

  • The sensor further comprises an aluminium plate which carries out injection molding, beam enveloping and forming with the upper cover;

    该 封闭式汽车油位传感器还包括一铝板,该铝板与上盖注塑射包成型。

  • The effect of process parameters on the electric insulance of micro arc oxidated ceramic coat on aluminium plate is studied.

    研究了工艺参数对铝微弧氧化陶瓷层电绝缘性能的影响规律。

  • The optimum technological parameters for the laser cutting of aluminium plate have been obtained.

    获得了激光切割铝板的较佳工艺参数。

  • Anodized aluminium plate Aluminium plate for offset printing with a specially prepared surface. SeeAnodizing.

    阳极氧化铝版版面经过特别处理的柯式印刷用铝版。参阅阳极投送化法。

  • A shadow moire method and its results for measurement of distortion of aluminium plate at exploding charge is presented. Possible errors are also estimated.

    本文介绍了用阴影云纹法测量爆炸载荷下铝板变形的方法及结果,并进行了误差讨论和静态标定。

  • The light base oil can be used in roll oil for aluminium plate production, as the feedstock of transformer oil or as the blending component of low viscosity lubricant.

    轻质基础油可作为生产铝板冷轧制用润滑油的基础油、变压器油的原料及作为低粘度润滑油调合组分。

  • The effects of cutting speed and aided oxygen pressure on the cutting quality and the adhesive slag quantity were analysed in the experiment of cutting of aluminium plate by CO2 laser.

    在CO2激光切割铝面板的试验中,分析了切割速度和辅助氧压对切割质量及熔渣附着量的影响;解决了工件逆反射的难题;获得了激光切割铝板的较佳工艺参数。

相关热词