英汉例句

• firstly, the attitude of the target was estimated according to cubic spline interpolation functions of the track, which avoided complex image processing and had higher speed.

  首先根据航迹三次样条插值函数估算目标姿态，避免了复杂的图像处理过程，计算速度快；

• firstly, comparing to neural network, cubic spline interpolation featuressimple operation and program development, but a smaller fit range.

  首先，三次样条插值与神经网络方法相比，使用方便，算法简单，但适用范围较小；

• connecting with example, the results of these arithmetic are compared, and the cubic spline interpolation is confirmed as a effective method to rectifying map.

  并结合实例，对上述几种方法进行比较计算，证实了用三次样条插值进行地图纠正的这种方法是可行的。

• the engine output torque model and oil consumption model are given in numerical table by cubic spline interpolation to fit engine test result.

  文中通过对现有的发动机实验数据进行数值拟合，以数表的形式给出了发动机的输出转矩模型、油耗模型。

• a cubic spline interpolation between inductances at low and high frequency gives a good result over the entire frequency range.

  对上述离散频率的电感值利用三次样条函数插值，得到整个频率范围内电感的变化曲线。

• the use of cubic spline interpolation function method can only solve the processing problem of nomographs consisting of one family curves.

  指出用三次样条插值函数法只能解决由一组曲线族组成的图表处理问题。

• principals of optimal piecewise cubic spline interpolation and applications of interpolant fitting to the thermocouple characteristic curves are introduced.

  介绍了优化的三次样条插值原理及对热电偶特性曲线的插值拟合应用。

• the cordic algorithm is adapted to convert the polar coordinate image to the rectangular coordinate image, while cubic spline interpolation is used to interpolate the vacant pixels.

  本文采用数字坐标旋转（cordic）算法将极坐标图像转化为直角坐标图像，并采用三次样条插值的方法对漏点进行弥补。

• extensive simulation and comparisons are carried out for the four interpolation techniques: linear interpolation, second-order interpolation, cubic spline interpolation and low-pass interpolation.

  论文仿真比较了线性插值、二阶插值、三次样条插值和低通插值四种插值技术。

• this dissertation researches in the vibrant clipped data of a plane, proposes regression analysis, bp learning algorithm and cubic spline interpolation to forecast the clipped data.

  以国产某型无人机空飞时振动传感器测得的振动削波数据为研讨对象，选用归归剖析法、bp神经网络法和三次样条插值法对削波数据入行预测恢复。

• finally, the subsection cubic spline interpolation was used to analyze the pitch curves which provide a method for the further work.

  最后运用三次样条插值对其节曲线了进行研究，这为后续的设计制作提供了一定的依据。

• the computational format and the software at finite element node based on the cubic spline interpolation function which has been improved by author have been presented.

  对三次样条插值函数进行改进，提出了有限元离散节点的计算格式及软件。

• cavitation curve drawing method of the traditional hand-drawn method, polynomial fitting, non-linear fitting, cubic spline interpolation method.

  汽蚀曲线绘制方法有传统的有手工绘法、多项式拟合法、非线性拟合法、三次样条插值法等。

• simulation of point target model is built. it is demonstrated that the cubic spline interpolation technique is a good method and can be applied in practice.

  用点目标进行仿真，结果表明：在雷达成像中三次样条插值是一种比较好的插值方法，可在实际中应用此方法。

• a monotonicity preserving rational cubic spline interpolation function is proposed and the interpolation functions is c1 continuous.

  构造了一种c1连续的保单调的有理三次插值函数。

• the meshing stiffness is calculated by employing 3-dimensional fem and its function is formed by cubic spline interpolation and approximation of the discrete mesh points in a mesh period.

  采用三维有限元法计算了斜齿轮副啮合刚度，用三次样条插值拟合得到时变啮合刚度函数。

• it is acquired from that it makes use of that the interpolation function of cubic spline interpolation has a continuous third derivative on the base of two-dementional cubic convolution interpolation.

  它在二维三次卷积插值法的基础上利用三次样条插值法的插值函数具有三阶连续导数的性质而得来的。

• introduces the application of cubic spline interpolation to restore the clipped data.

  提出了利用三次样条插值对被削波数据进行恢复的方法。

• cubic spline interpolation is used to create the upper and lower envelopes in traditional emd process, which has worse behavior at the edges, and influences the quality of signal process.

  在已有经验模式分解的过程中，由于常用三次样条插值来拟合信号的上下包络，因此时常会出现边缘效应，从而影响了信号处理的质量。

• by comparison of several interpolations, because of the best tradeoff between accuracy and the computational cost, cubic spline interpolation is selected as interpolation of this paper's registration.

  首先通过对配準中所采用的几种插值算法进行了比较，选出了有较高插值质量和有较高计算效率的三次样条插值算法作为本文中配準方法所采用的插值。