片语

radial depth of cut径向切削深度

limit depth of cut界限切削深度

Depth of cut notching深切凹口

depth of the cut割口角度

optimum depth of cut最佳挖掘深度

critical depth of cut临界切削深度

depth of tariff cut[税收]

英汉例句

• This particular model predicts the depth of cut achievable with any given set of process parameters.

  这个模糊控制模型可以预测在任何给定一组加工参数时，可获得的切割深度。

• Besides, if the feed and depth of cut is increased, the lubrication effect will become poor, and the reducing extent of the cutting force will be reduced.

  此外，增大进给量和切削深度，会使切削液润滑效果变差，切削力下降的幅度减小。

• They provide a constant depth of cut and fewer blade changes.

  它们提供了切不断深入和减少叶片的变化。

• The conditions which have an important influence on metal cutting are work material, cutting tool material, cutting tool geometry, cutting speed, feed rate, depth of cut and cutting fluid used.

  对金属切削有重要影响的条件有工件材料、刀具材料、刀具几何形状、切削速度、进给率、切削深度和所用的切削液。

• The axial feed is provided by the carriage or the compound rest, either manually or automatically, whereas the depth of cut is controlled by the cross slide.

  轴向进给通过大拖板或复式刀架手动或自动提供，然而切削深度则由横向滑板控制。

• During a facing operation, feed is provided by the cross slide, whereas the depth of cut is controlled by the carriage or compound rest.

  在端面车削操作中，进给由横向滑板提供，而切削深度则通过大拖板或复式刀架控制。

• As we can see in that figure, the depth of cut (and consequently the load) gradually increases on the successively engaged cutting edges.

  就像在此图中能看到的那样，切削深度(及作为结果的载荷)随着切削刃持续进入切削而逐渐增加。

• It can also be seen that the maximum depth of cut is achieved directly as the cutter engages with the workpiece.

  还可以看到当刀具进入工件切削时直接达到最大切削深度。

• Grasping the top, knurled section of the depth adjustment rod (Q), slide it up so that the TAB (EE) aligns with the desired depth of cut on the pillar scale (FF).

  抓住深度调节桿(Q)的顶部，向上抽，使定位片(EE)的顶面对正柱形尺(FF)上希望的切削深度。

• A quadratic model of predicting helical milling force was researched. The effects of spindle speed, feed per tooth, and axial and radial depth of cut were analyzed.

  通过统计学中的响应曲面法建立了螺旋铣削过程中切削力的二阶模型，并分析了主轴转速、每齿进给量、轴向和径向切削深度等因素对切削力的影响。

• In many cases of stainless steel cutting operations with carbide tools, a tool life strongly depends on flank notch wear of depth of cut rather than average flank wear of main cutting edge.

  硬质合金刀具在不锈钢加工中，其刀具耐用度主要是取决于后刀面边界磨损而不是主切削刃后刀面的平均磨损量。

• In this paper, effects of depth of cut and feedrate on mechanical properties of metallic fiber are investigated by spinning bit.

  研究了用自旋转车刀加工金属纤维时，切削深度和进给量对纤维力学性能的影响。

• Dry and wet masonry blades provide a consistent depth of cut with less dust than abrasives.

  干湿砖石刀片提供少于磨料粉尘削减一致的深度。