片语

electroslag melted电渣熔铸

electroslag welder电渣焊机

electroslag refining电渣精炼

electroslag furnace电渣炉

electroslag cladding电渣复合

electroslag weldment电渣焊缝

electroslag welding[机] 电渣焊

electroslag pressure电渣压力

electroslag weldnig电渣焊

英汉例句

• The origin of square segregation in high speed tool steel bars in electroslag refining is analyzed.

  对电渣重熔高速钢轧材方型偏析形成原因进行了分析试验。

• Traditional electroslag remelting technology has the disadvantages of polluting environment and extremely high specific power consumption.

  传统的电渣重熔工艺存在着污染环境和比电耗过高的弊病。

• Experimental investigation of peculiarities of electroslag remelting of waste titanium chip to produce high-Ti ferro-titanium has been performed.

  在有衬电渣炉内，对采用废钛屑为原料生产高品位钛铁合金的工艺进行了试验研究。

• The cold rolling roller blank was normally made out of electroslag and ingot but was limited in higher production cost and product specification.

  冷轧辊辊坯普遍采用电渣钢锭制造，但生产成本高、产品规格受限。

• The re-bar end used for electroslag welding should be straight, flat and clean free of U-shaped, bruising, concave and convex, bending or distorted deformations.

  电渣压力焊焊接使用的钢筋端头应平直、干凈，不得有马蹄形、压扁、凸凹不平、弯曲扭曲等严重变形。

• In this paper, the application of morden control theory to electroslag remelting process controlled by a minicomputer is recommended.

  本文介绍现代控制理论在电渣重熔计算机控制中的应用。

• The new development and application of electroslag casting technology at home and abroad are introduced, and a view on the development direction of electroslag casting technology is given as well.

  综述了近年来国内外电渣熔铸工艺的进展及工业应用，并对今后的发展方向提出了自己的看法。

• Electroslag remelt (ESR) furnace is the key equipment for the electroslag remelting process.

  电渣重熔炉是电渣重熔过程的典型设备。

• The composition, functions, PLC model selection and program design of PLC plus frequency speed- regulating system on electroslag furnace are briefly introduced.

  简要介绍了电渣炉PLC加变频调速控制系统的组成、功能及PLC的选型和程序设计。

• The quality and service performance of large cold roll produced by electroslag remelting (ESR) ingot can be obviously improved.

  电渣重熔(esr)钢所生产的冷轧辊能显着改善冷轧辊质量，提高轧辊使用性能。

• It is pointed out that electroslag technology is an ideal process of manufacturing gigantic ingots for 100t up to 300t forging a piece.

  指出，电渣技术是生产100t以上直至300t重大锻件用巨型钢锭的理想方法。

• The fine metallurgy for extra cleaning high quality metallic material has been developed continuously and the recent development of electroslag metallurgy is obvious.

  制备超纯优质金属材料的精细冶金不断地向前发展，近期电渣冶金的进展令人瞩目。

• The features and problems of manufacturing high nitrogen steels by the electroslag remelting method at normal atmospheric pressure and high pressure have been discussed in detail.

  概述了目前高氮钢的主要制备方法，重点讨论了常压和高压电渣重熔高氮钢的特点和存在的问题；

• In the process of making the complex and various sections casting by electroslag casting method, it will frequently occur serious accidents that the crystal instrument would be always destroyed.

  在使用电渣熔铸方法生产变截面复杂铸件的过程中，经常会发生结晶器被侵蚀甚至击穿的重大事故。

• The procedure using anneal instead of normalizing will improve the productive efficiency of electroslag welding joint.

  用退火代替正火后的电渣焊工艺可大大提高生产效率。

• When producing the rare earths Fe-Cr-Al alloy by electroslag remelting method, the optimum quantity of rare earths added to three phase lining electroslag furnace is 0.5%.

  电渣双联法生产稀土铁铬铝合金时，稀土在三相有衬电渣炉中的最佳加入量为0.5%。

• The flow of the molten slag pool determines the temperature distribution and the pool profiles in the electroslag casting process, which affects the quality of ingot casting.

  电渣熔铸过程中熔渣的流动决定了熔铸体系温度场的分布以及金属熔池的形状，最终影响熔铸钢锭的质量。

• Nickel rod needs to be lengthen by argon arc welding before the electroslag refinements, large welding parameters are needed to assure the sufficient penetration.

  金属镍在电渣精炼前需用氩弧焊焊接接长，为保证焊接接头具有足够熔深，需要大参数进行焊接。

• In this paper, technical principle on preparation of metal mould by casting method of electroslag smelting and application prospect is described.

  本文简述了用电渣熔炼浇铸法制备金属模具的工艺原理和该方法的应用前景。

• The products of electroslag remelting steel include 243 designations of alloy steel and superalloy.

  产品包括优质合金钢与超级合金243个牌号。

• It is presented that the switch control with dead limits drives a motor to accomplish the control requirement of automatic feeding of cousumable electrode in electroslag casting of heavy crankshaft.

  介绍了带死区的开关量控制在大型曲轴电渣溶铸中驱动电动机，以实现自耗电极的自动进给要求。

• The deepness of slag pool is one of the most important technics parameters in the electroslag casting process, which affects stabilization of the process and product's quality.

  渣池深度是电渣熔铸过程中重要的工艺参数之一，它直接影响到熔铸过程的稳定和产品质量。

• This article describes three stages in the development of electroslag furnace and its recent development.

  系统论述了电渣炉发展的三个阶段，以及电渣炉最新发展。

• The detection environment, method and new progress of electroslag casting are introduced.

  介绍了电渣熔铸金属液位的检测环境、方法和最新成果。