片语

end-face coupling端面耦合

side surface端面

end-face seal端面式机械密封

end-face friction端面摩擦

head face端面

end capacity face seal端面密封

end d face端面

drive end housing face主动端壳体表面

end-face quality端面品质

large end-face大端面

end plane端面

End and face milling立铣和端铣

英汉例句

• it has been theoretically derived that the far field is also a gaussian distribution provided that the near field on the output end face of single mode fiber is gaussian distribution.

  本文在假定单模光纤横端面上的近场为高斯分布的前提下，从理论上导出了其远场分布也是高斯分布。

• the method is to inject tungsten into the work end face of the spot welding electrode to improve the performance of the electro de.

  采用离子注入钨方法在点焊电极工作端面注入钨以改善电极性能。

• tall curtain walls at either end face the cégep to the east and the woods to the west, letting in morning light on one side and evening light on the other.

  幕墻的两端分别对应东部学生区和西部树林，由此让早晨和晚上的光照向不同的面。

• when the pumping is exhausted, we used the example to deduced the specific pressure computation of the machine seal's end face and the change condition of the seal parameter.

  用实例说明泵运行出现抽空操作的端面比压计算以及密封参数的变化。

• the principles of single contour connection, furcation processing and triangular patch division of end face have been introduced in great detail with specific algorithms.

  首先详细地介绍了单轮廓连接、分叉处理及端面三角面片剖分原理，同时给出相关具体算法。

• cylinders, straight cups, and flaring cups are used for surface grinding with the end face of the wheel.

  用其端面进行表面磨削的圆柱、直杯及外展杯状砂轮。

• with the face grinding attachment , perpendicularity of the end face to the bore after grinding can guaranteed.

  带有端磨装置，保证工件端面与孔的垂直度。

• it is helpful for the basically theoretical researches and the design of end face harmonic gear drive of oscillating teeth. and it has a definite application expectation and economic value.

  关于活齿端面谐波齿轮啮合副的齿面方程及其修形的理论研究，奠定了活齿端面谐波齿轮减速器设计的理论基础，为这种新型传动装置的推广应用铺平了道路。

• three kinds of injection sleeves construction, materials, surface treatment and application ranges of floating end face seal ring by die casting are expounded.

  叙述浮动端面密封环压力铸造的三种压射套结构、材料和表面处理工艺及其应用范围。

• end face with a gap, no boss butt is refers to the upper and lower casing left a certain gap between the upper and lower main chord rod end face at the same time contact.

  端面有间隙、带凸台对接外形是指在标準节上部主弦桿上焊有定位凸台，定位凸台伸人另一标準节主弦桿内，上、下套管之间留有一定间隙配合定位。

• the advantages of mechanical seals are described in the article. mechanical seals are classified into: balanced seals and unbalanced seals, contacting seals and non-contacting end face seals.

  平衡型密封与非平衡型密封、接触式机械密封与非接触式机械端面密封；

• the magnetorheological valve utilizes a scheme of arranging a nonlinear flow passage on a corresponding end face of a locating disc and a concentrating flux disc.

  采用的方案是，定位盘与导磁盘的对应端面上，设置非直线 形液流通道。

• the construction of a new type anti-pitting tappet with a cast hole in its end face and isothermally treated are described.

  介绍了端面直接铸孔并进行等温处理的新型抗点蚀挺桿体的结构和热处理工艺；

• the wear rate of the end face of soft ring of b104a -70 mechanical seal was calculated and analyzed.

  对b104a-70型机械密封软质环端面的磨损率进行了计算和分析。

• based on analyzing the gear parameters, the grinding of the gear face with an end face of the grinding wheel was realized by changing the rotating angle of rotating table.

  在对齿轮参数进行数学分析的基础上，通过改变数控回转台的旋转角度，实现了用砂轮的一个端面去磨削齿轮的齿面。

• the modification principle of tooth surface is deduced, and it draws the conclusion that the modificative tooth depth of wave producer, end face gear and oscillating teeth have certain relation.

  研究了活齿端面谐波齿轮各啮合副齿面修形的原则，得出了波发生器、活齿前后端和端面齿轮齿面的修形高度之间必须满足的关系。

• architecture design plan, elevation, end face figure and other completed design plan.

  建筑设计平面图、立面图、顶面图等其他完整的设计方案。

• the conclusion will be useful for the design of structure for similar floating end face seal and make possible the further study of its mechanism.

  对同类浮动端面密封结构的设计有指导意义，并使进一步研究浮动端面密封的机理成为可能。

• the equations of teeth surface after modification of all key components, such as wave producer, oscillating teeth, end face gear, are deduced.

  推导出了活齿端面谐波齿轮各啮合副经过齿面修形后的齿面方程。

• in this paper, the engagement theory of the end face harmonic gear drive of oscillating teeth is studied; and the normal solution procedure is given.

  研究了活齿端面谐波齿轮的啮合原理，给出了一般的求解步骤；并在保证瞬时传动比恒定的条件下，推导出了波发生器与活齿后端啮合副的一种齿面方程。

• this paper will proposed a machine vision-based optical fiber ferrule end face detection system design and implementation to satisfy the actual demand inside the factory.

  本文针对工厂里的实际需求，提出了一种基于机器视觉的光纤插芯端面缺陷检测系统的设计与实现方法。