英语释义

1. something (such as a device or software function) that indents a text or document
A text editor … with lots of programming related commands including a very smart indenter.
— Steve Oualline

2. a tool used to make a physical impression or indentation
The researchers used an indenter … to create microscopic pits on the surface of each molar.
— Alexandra Goho

片语

cone indenter锥构刻压仪

diamond indenter[仪] 金刚石压痕计

standard indenter标準压头

indenter shape压头形状

blunt indenter钝化压头

conical indenter圆锥压头

Coating indenter涂层压入仪

asymmetric indenter非对称压头

Vickers Indenter显微维氏硬度计

英汉例句

• type d also owns objective magnification and indenter automatic switching devices.

  型还拥有测量物镜与压头自动切换装置。

• the behavior of aln subjected to micro indentation with random load by a cylindrical flat punch indenter was analyzed by finite element method for the first time.

  用有限元法分析了在随机加载的圆柱形刻痕器作用下氮化铝的行为，模拟了应力场的整个扩展过程。

• the method was described clearly. in the deflection of microbeams, the influence of the indenter tip pushing into the top of the microbeams and the curvature across its width must be considered.

  运用该方法在研究微悬臂梁的弯曲形变过程中，必须考虑压头在微悬臂梁上的压入以及微悬臂沿宽度方向的挠曲。

• the finite element method was used to model situations where an indenter applies normal forces to a coated or uncoated aluminum substrate.

  应用有限元法对由压头向涂层或未涂层铝基体施加正压力的情况进行模拟。

• the applied load, shape of the indenter and properties of substrate that have influences on microhardness test result have been studied.

  研究了施加载荷、压头形状、基板性质等因素对涂层显微硬度测试结果的影响，得出了为準确确定涂层硬度指标所适合的试验条件。

• the effect of indenter size on response of indentation creep is discussed in detail, and two methods to determine the creep property parameters of the interlayer zone is presented with illustrations.

  详细地研究了压头大小对压痕蠕变响应的影响：提出两种方法由压痕蠕变试验来确定界面影响区蠕变性能参数，并给出了算例。

• the effect v-ring indenter on the sheared surface in the fine blanking of shifting fort is investigated by means of finite element method.

  使用有限元分析法对拨叉零件的精沖过程中v形齿圈对沖剪面的影响进行了研究。

• a new area function is introduced and applied to a berkovich tip in order to characterize the contact projected area between an indenter and indented material.

  为了研究纳米硬度计压针尖端曲率半径对面积函数的影响，提出一个基于几何方法建立的压针面积函数。

• on a few metal hardness instruments, major equipment is on a different angle conical diamond indenter or different diameter ball pressure on the first loading of the metal to surface make indentation.

  介绍几个关于金属材料硬度仪器的研制，仪器主要是依靠不同角度的角锥金刚石压头或者不同直径的钢球压头依靠加卸载力来对金属表面做出压痕。

• the mechanic properties (e, s) of hydride are analyzed by nano indenter ii.

  用显微力学探针分析了氢化物的力学特性。

• fix the controller at the required height in the graduated guide-tube ; and press the control screw , the cylinder will fall on the indenter and then transfer the impact on the film panel .

  用控制器螺钉固定好高度，按压控制螺钉，重锤即自由落在沖桿上，沖桿将沖击力传到样板上。

• it demonstrated that the experiment of hardness is likely to upset in the experiment of compression. hardness tester indenter make matrix metal plastic deformation and viscous flow happen.

  结果表明，硬度实验类似于压缩实验中的镦粗，硬度计压头可使金属基体发生塑性变形及粘性流动。

• mechanical characterisation of paint coatings using an indenter with force or velocity measurement!

  使用压力方式或者速度方式的压痕对油漆涂层的机械性能进行测量的方法。

• an accurate account of the contact problem of an elastic indenter and a laminated beam is given by using the mixed finite element method for solving elastic contact problems.

  本文采用处理弹性接触问题的有限元混合法研究了弹性压头与复合材料层合梁间的弹性接触问题。

• through the experiments, it was also found that the deformed dlc films exhibit about 15% elastic recovery, and considered that knoop indenter was more suitable for hardness measurement of dlc films.

  通过试验还发现dlc膜有约15％的弹性恢复，并认为dlc膜的硬度测定采用克努普压头更为恰当。

• xrd, nano indenter and profiler were employed to investigate the influence of the modulation period on microstructure, mechanical properties of the coatings.

  通过xrd和纳米力学测试系统以及摩擦磨损仪分析了该体系合成以后的晶体结构，以及调制周期对机械性能的影响。

• the fracture toughness kic of tialn coating has been measured by weishi indenter indentor and the appearance of impress has also been observed by sem.

  并采用维氏压头测量断裂韧性kic和通过扫描电子显微镜观察压痕形貌来评定涂层的韧性。

• the cutting force equations of taper indenter are derived from rock mechanics at the first. it is concluded that cutting force is proportional to the square of cutting depth.

  首先应用巖石力学理论导出了锥压头切削力的计算公式，得出切削力与切削深度的平方成正比即与切削沟槽横截面积成正比的结论。

• hardness testing consists of pressing an indenter into a flat surface under a perfectly controlled load, then measuring the dimension of the resulting indentation.

  硬度测验是指将一个锯齿状产品在控制的很好的力度下压进平滑的表面。然后测量所造成的压痕的尺寸。