英语释义

1. entrance

2. a thing that enters import

3. import duty

4. a gate through which the metal is poured into a foundry mold

片语

center ingate中心浇道

unilateral Ingate单侧马头门

Ingate Speed内浇口速度

mine ingate立井马头门

triangular ingate三角形进模口

Arc Ingate弧形内浇道

ingate velocity内浇口速度

cytostome细胞口；入口孔

Ingate Pass街道地址

ingate sleeve浇口套

英汉例句

• it is suggested to apply the principle of effective gravity and equivalent pressure head to calculate the rotational speed and ingate area in the processing of grinding ball by centrifugal casting.

  在离心铸球工艺中，可应用有效重度和等效压头原理计算转速和内浇口断面积。

• there easily exists shrinkage porosity due to superheat of ingate root in large plain parts investment casting.

  大平面铸件常在内浇道根部出现过热，在该处产生缩松缺陷。

• the results show that the casting with good quality can be obtained by removing one ingate and adding cooling waterway into mould.

  结果表明，采用去掉一个内浇口，增加模具冷却水道的工艺可获得质量较好的铸型。

• the small formation holes in the brush cover was constructed with the mold core in moving and static container, and center ingate was employed to the gating system.

  针对电刷端盖压铸件结构及工艺要求，选择端盖口部大端面为动静模分型面，铸件上各成形小孔由动静模型芯对接组成，浇注系统采用中心浇道。

• acentric ingates are used to set on the moving mould and slag-collector is set at the end of ingate and at converging zone of liquid metal from two sides.

  选择偏心的分支浇道，并将浇道设置在动模一侧。在浇道的末端和两侧金属液汇集区域分别设置集渣包。

• improvement of the running system is proposed by the further tests of water simulation, that is, adjusts the ingate installation to decrease the trapped blowholes.

  水力模拟的进一步试验，提出了改进原浇注工艺的措施，改变内浇道设置以获得较好的充型效果，从而达到减少卷入性气孔的目的。

• using thin, wide ingate and chill can prevent the shrinkage defect, and improve casting yield by 3%.

  采用薄、宽的内浇道和冷铁工艺消除了飞轮铸件的缩孔缺陷，铸造工艺出品率提高3%；

• it is found that the shape and size of ingate of thin walled plate casting have a tremendous influence on the temperature field during solidification and its quality.

  发现内浇口的形状和尺寸对铸件凝固过程中的温度分布及铸件品质影响很大。

• the technology of grinding ball by centrifugal casting, the rotational speed, the method for calculation of ingate area and factors influencing technological process were introduced.

  介绍了离心铸造磨球的工艺，以及转速、内浇口断面积计算方法和影响工艺过程的因素。

• ring pouring channel was set for pouring position. ladder-like horizontal gate was designed for horizontal gate. section area of ingate was calculated by the equation.

  浇道位置为环形浇道，横浇道设计成扁梯形横浇道，内浇道截面面积根据公式求取。

• using short, thin, wide ingate and chill to prevent the shrinkage defects, casting yield was improved by 3%.

  采用短、薄、宽的内浇道和冷铁工艺，消除球铁飞轮铸件的缩孔缺陷，铸造工艺出品率提高3 % ；

• the computer simulation results showed that the effects of ingate dimension and ingate location on the rheo-diecasting were relatively small and the casting process-design was easily to be done;

  结果表明：半固态流变压铸成形在不同的内浇口尺寸与位置条件下都可以获得平稳的充型流动场，其工艺参数设计灵活；

• the crack in investment castings is commonly created around ingate due to easily forming superheating at root of ingate.

  铸件内浇道根部易出现过热，裂纹一般产生在靠近内浇道处。

• the original ingate was enlarged by side cutting and roof cutting under the condition of filling behind wall by grouting, and then be supported and reinforced by the secondary support technology.

  原马头门断面不能满足矿井安全需要，需对原马头门进行断面刷大，采用刷帮挑顶技术。

• effects of sss die casting processing parameters on properties of adc12 aluminum alloy castings were examined by a standard tensile testing specimen with different ingate configurations.

  研究了不同内浇口速度、内浇口形状对超低速adc12铝合金压铸件性能的影响规律，探讨了不同内浇口速度和尺寸对铸件微观组织及力学性能的影响。

• the results show that the submerged nozzle ingate angle and depth of its immersion should decrease gradually with the lowering of casting speed.

  结果表明，随着拉速的降低，水口的上倾角大小和浸入深度应逐渐减小。