英语释义

• a manifold consisting of a pipe to carry fuel to each cylinder in an internal-combustion engine

片语

intake manifold tuning进气歧管调谐

intake e manifold进气歧管

english Intake Manifold进气歧管

intake manifold runner control进气歧管通路控制

tuned intake manifold调谐进气歧管

vacuum from intake manifold来自进气歧管真空

intake air manifold进气歧管

Plastic Intake-Manifold全塑进气歧管

hose intake-manifold outlet进气歧管出水管

英汉例句

• like a traditional intake manifold for6-cylinder flat-six engines the expansion intake system consists of a distributor pipe two accumulators and six individual intake ports.

  与水準对置6缸发动机的传统的进气管一样，新款车的膨胀进气系统由一个分配器管、两个储气罐和六个独立的进气口组成。

• the second part carries on the air fluid simulation analysis of variable intake manifold with the star-cd fluid software.

  第二部分用star-cd流体软件对可变式进气歧管进行空气流动数值模拟分析。

• this paper introduces the calibration system and static and dynamic calibration method of an engine intake manifold pressure sensor.

  介绍了发动机进气歧管压力传感器的标定系统和传感器静、动态标定方法。

• the flow characteristic of intake manifold has sensitively influence on engine, including economy performance, dynamical performance and the level of injurant emission.

  其流动特性对发动机性能的影响十分敏感，其优劣影响到汽车的经济性、动力性和有害物排放的水平。

• the piston moves up and down in the piston chamber primarily in response to changes in intake manifold vacuum .

  活塞主要因进气歧管真空度的变化而在活塞腔内上下移动。

• the intake manifold connects the carburetor to the intake ports of the engine.

  进气歧管把发动机进气道口连接起来。

• gm also says the mill will be 「one of the quietest and most refined engines in the segment」 because of an acoustic intake manifold cover and inverted-tooth camshaft chains.

  另外，gm表示新引擎将是「同级之中其中一款最宁静及最精细引擎」，因为新引擎采用一个静音进气歧管盖及倒齿式凸轮轴链条。

• this device, called the manifold heat-control valve, is built into the exhaust and intake manifold .

  这种装置称为「歧管热控制阀」，它拼装在排气与进气歧管中。

• the intake manifold casting was machined to fit and bolted in place between the heads.

  在进气歧管铸造加工，以适应和螺栓在两国元首。

• in order to improve engine efficiency and torque as well as the engine performance, plastic intake manifold was developed for ca4ge engine.

  为了提高发动机的效率和扭矩、改善发动机的性能，针对ca4ge发动机研究、设计、开发了发动机塑料进气歧管。

• fine adjustments to intake timing can be made by rotating the intake manifold in the plastic friction mounts in either end of the block.

  精细调整，以摄取时间，可旋转的进气歧管的塑料摩擦安装在两端的区块。

• the velocity-pressure wave method requires the measurement of both the average velocity wave and the pressure wave of intake manifold near the valve at the same cross section;

  应用流速—压力波法，须测量各缸进气歧管靠近进气门处的平均流速波和同一测量截面的压力波；

• the throttle body assembly will mount to the manifold snout and intake manifold interface dimensions are defined on the throttle body assembly outline drawing.

  节气门体总成安装在歧管口，进气歧管接口尺寸如节气门体总成轮廓图所示。

• compressed air is injected at the left end of the intake manifold tube.

  压缩空气注入在左端进气歧管管。

• this thesis mainly carries on research of three dimensional surface reconstruction of variable intake manifold and air fluid simulation analysis.

  本文主要进行可变式进气歧管的三维曲面重建和空气流动模拟分析的研究。