英语释义

• any of various rotating shafts that serve as axes for larger rotating parts

片语

riser mandrel隔水导管紧轴

mandrel mill芯棒式轧管机；芯棒式无缝管轧机

roll mandrel辊轴

expansion mandrel胀缩心轴

stretching mandrel扩张芯轴

adjustable mandrel可调心轴

mandrel colier筒式卷取机

link mandrel滑动心轴

mandrel extractor芯棒抽出机

drift mandrel偏移心轴

英汉例句

• after the consolidation of the composite ring in tension winding, the mandrel is drawn out, and then a hollow ring is formed.

  纤维束张紧力缠绕的复合材料厚环固化成型以后，再抽出缠绕芯轴形成空心环，这一过程称为内孔卸载。

• after the mandrel is melted, a thin layer of alloy remains on the propellant surface.

  此心轴溶化之后，在推进剂表面上留有一薄层的合金。

• a hole is drilled in the center and it is bolted to a mandrel so that the rest of the machining operations can be performed.

  鉆一个洞，是在中央，这是一个心轴螺栓，使其余的加工操作可以执行。

• a 「position effect」 usually occurs in cold bending test of ribbed steel bars, when the bending mandrel is misaligned with the bar surface.

  冷弯试验时，钢筋表面相对弯芯放置位置不同，钢筋的变形部位将产生「位置效应」。

• ensure that the lathe dog is secured to the machined flat on the end of the mandrel and not on the smooth surface of the mandrel taper (figure 7-44).

  确保车床轧头牢牢地固定在心轴端的机械平面上，而不是锚定在锥形心轴的平滑面上（图7-44）。

• the results show that: the springback angle of bent tube increases with the bending angle, the gap between mandrel and tube, and the hardening coefficient, but decreases with the hardenability value.

  结果表明：回弹角随弯曲角、芯棒与管壁间隙及材料硬化系数的增大而增大，随材料硬化指数的增大而减小。

• corey electrical appliance factory is a set of design, production, research and development all kinds of electric heaters, screw elements, barrel, mandrel specialized factory.

  科瑞电器厂是集设计、生产、研发各类电加热器、螺纹元件、机筒、芯轴的专业厂家。

• spiral mandrel blown-film die is advanced and widely used in film blowing which is one of the most popular processing for plastics film.

  薄膜挤出吹塑是应用最广泛的塑料薄膜加工方法之一，而螺旋芯棒式机头则是应用最为广泛的、先进的吹膜机头。

• electric heater, screw elements, barrel, mandrel series of production, living in the same industry-leading level of domestic.

  电加热器、螺纹元件、机筒、芯轴系列产品的生产，居于国内同行业的领先水平。

• the microcomputer controlled filament- wound machine for forming tee pipe, processing mechanism, and mandrel design are given in this paper.

  本文简单介绍了由计算机控制纤维缠绕三通管的设备工作原理及芯模设计。

• the structural design of molding mandrel of pyrophillite was improved.

  对叶块成型芯轴的结构进行了设计改进。

• the rubber tube was expansed after inflated, then closed. the soft core that could be favourable to mandrel stripping was used to rubber special tube.

  用一纯橡胶管充气后使其膨胀然后将其封闭，用作橡胶异型管生产中使用的软芯，能够有利于脱芯。

• the formulas introduced for design of the parabolic mandrel and pass are worth referring to.

  引用的抛物线芯棒及孔型设计公式可供参考。

• the mandrel must be mounted between centers and a drive plate and lathe dog must be used.

  必须将心轴锚定在中心点和驱动板之间的位置，并且必须使用车床轧头。

• through experiments, the method and values to ensure spinning technology parameters of no - mandrel roller were gained.

  通过实验，给出了无心轴托辊管体的旋压过程中工艺参数的确定方法和数值。

• mount the workpiece onto a lubricated mandrel of the proper size by using an arbor press.

  通过利用杠桿式沖床将工件锚定在适当尺寸的润滑心轴上。

• winding the silk solution on a rotating mandrel provides control of tube properties like winding pattern, tube porosity and composite features.

  将丝蛋白溶液涂在旋转卷筒上，可以对图案、管开孔率以及复合特性进行控制。

• hardware and software configuration of drive system with position controller, dc drive unit and plc for a retainer of semi-floating mandrel mill are analysed.

  分析了由位置控制器、直流传动装置和plc组成的半浮芯棒连轧机组限动链控制系统的硬件配置及软件组成。

• the fracture mode of cold-rolling mandrel is mainly early fatigue fracture.

  冷轧芯辊的失效方式主要是过早疲劳断裂。

• advantages of employment of semi-floating mandrel mill to produce small and medium tubes are elaborated.

  提出了小型无缝钢管生产机组选用半浮动芯棒连轧工艺的优势。