片语

signal measured测量信号

measured signal converter测定信号转换器

measured signal segregation测量信号分离

Signal Measured Element信号测量单元

measured d signal被测信号

measured signal decoupling测量信号解耦

measured burst signal setup time被测猝发信号建立时间

英汉例句

• The measured signal needing by system popularly can be divided into two kinds which are on-off quantity and analogy quantity.

  系统需要的被测信号，一般可分为开关量和模拟量两种。

• In the process of microwave measurement, adjusting the level of the measured signal is an important part.

  微波测量过程中，对不同电平的被测信号进行电平控制，是测量过程的重要步骤。

• On the one hand, by calculating the general dimension of the measured signal and extracting its sensitive dimension, the crack fault of measured signal is diagnosed and identified.

  一方面，通过计算实测信号的广义维数，提取其敏感维数，进而对实测信号的裂纹故障进行诊断识别。

• The BZGK2 protector to the sensor take two exchanges signals sampling, the measured signal approaches to the real value, it had guaranteed the examination is accurate.

  BZGK2型保护器直接对传感器二次交流信号采样，所测信号最接近真实值，保证了检测的準确型。

• Two-velocity analysis method can develop the pile integrity test, average wave speed and wave-up curve separated from measured signal under the condition of existed foundation.

  采用双速度测试和分析技术可以解决在既有基础下基桩的完整性、平均波速以及从实测信号中分离出上行波曲线。

• Analysis of measured signal of low resistance cable fault shows that: the method reduces deviation of singularity detection and improves precision of fault location.

  测得的信号低电阻电缆故障的分析表明：这种方法可减少偏差的奇异性检测，提高了故障定位的精度。

• The diagnosis strategy based on model is proposed, which realized fault diagnosis in terms of the errors of real-time measured signal and the outputs of the global and local diagnosis model.

  把系统全局的和局部的预测模型的输出与实际输出比较，根据残差就得出相应的诊断结果。

• The centralized control device for set includes port for inputting measured signal from sensor.

  机组集控装置设有传感器测量的信号输入端口；

• The noise in the measured signal is constrained to 「white」 noise or at least nearby 「white」 noise.

  这要求被测信号中的噪声为白噪声或至少接近白噪声。

• The cymometer makes use of equal-accuracy design that can overcome the disadvantage of traditional measuring principle, which precision declines as measured signal frequency does.

  该频率计利用等精度的设计方法，克服了基于传统测频原理的频率计的测量精度随被测信号频率的下降而降低的缺点。

• The research result shows that the new algorithm has fast convergence speed and good precision. The method is suitable for the on line tuning of a measured signal on industrial plant.

  研究结果表明，该方法具有很快的收敛速度和很好的拟合精度，适用于工业过程中测量信号的在线校正。

• This paper particularly analyze the relation between frequency of measured signal and frequency of count pulse on measuring precision.

  文中详细地分析了被测信号的频率和计数脉沖的频率与测量精度之间的关系。

• For the factors of bearing using conditions, installation, and load, etc., the measured signal is often mixing with a variety of interference signals.

  又因为轴承的使用状况、安装的情况和载荷等等因素，测得的信号往往是含有多种的干扰信号。

• Using the filter property of correlative Integral, the effect of noise in measured signal may be effectively restrained and the precision of parameter estimation is raised.

  利用相关积分方法的滤波特性可以有效地抑制测量信号中的噪声影响，提高参数估计的精度。

• The experimental results show that from stationary and SNR of two aspects on random data to evaluate the measured signal quality is feasible, can evaluate the real bridge signal quality preferably.

  结果表明，论文提出的从随机数据的平稳性和信噪比两个方面去评价桥梁环境振动响应信号质量是可行的，可以较好地评价实桥信号的质量。

• The resulting offset voltage is subsequently subtracted from the measured signal to maximize measurement accuracy.

  随后从被测的信号中减去测量出的偏置电压，以便最大限度地提高测量的準确度。

• While using MCU as detecting system, input channels of measured signal should always be demanded in the system, and the necessary input information is collected by computer.

  当将单片机用作测控系统时，系统总要有被测量信号的输入通道，由计算机拾取必要的输入信息。

• In a self-designed dynamic error experimental system, the standard signal (motor pulses) and the measured signal (grating pulses) were collected synchronously, and isolated the dynamic error.

  在自行设计的动态误差实验系统中，同步采集标準信号（电机脉沖数）和测量信号（光栅脉沖数），实时比对分离出动态误差。