片语

measurement the error测定误差

measurement U error量度误差

measurement method error analysis误差分析

inaccuracy of measurement测量误差；测量的不準确度

measurement measurement error登记测量测量误差

measurement E error量度误差

metering error[测] 测量误差

Measurement System Error量测系统误差

Punching Measurement & Error沖击测量及误差

英汉例句

• What is the impact of measurement error and impurity type on temperature compensation?

  杂质组分以及测量误差对温度补偿有哪些影响？

• The new algorithm has better performance than the Sunzi algorithm because it can rectify the measurement error and can resolve Doppler ambiguity as well as range ambiguity.

  这种算法对测量误差不敏感，而且既可以解距离模糊又可以解多普勒模糊，所以它的性能优于孙子定理算法。

• From a numerical simulation on a practical possible mode: uniform acceleration-uniform speed-uniform deceleration we obtain the relationship between the measurement error and the acceleration value.

  以匀加速-匀速-匀减速运动为例，分析了测量误差与加速度之间的关系，模拟结果验证了该方法的可行性。

• The result shows that the scheme has the features of high precision and intelligence, and the manual measurement error is reduced.

  结果表明，该方案具有实现精度高、智能化的特点，减小了人工测量误差。

• Error analysis showed that the measurement error is usually less than 10% for low void fraction flow. So this is a lowcost and accurate measurement method.

  误差分析表明，这种测量方法在低空泡率条件下测量误差一般不超过10 %，它是一种低成本、高精度的绝对测量方法。

• Using the linear model with measurement error paddy production was estimated by means of NDVI.

  用含测量误差的线性模型，由植被指数(NDVI)估计稻谷产量。

• The experiment results show that this method can decrease the influence of measurement error on identifying precision and improve balance precision.

  结果表明该方法能有效抑制测量误差的影响，提高识别与平衡精度。

• Compared to the area measurement by a mono-resolution dynamic contour, this scheme is more robust with the smaller average error, single measurement error and iteration error.

  与单分辨率动态轮廓线面积测量方法相比，该方法具有鲁棒性强，平均值误差、单次测量误差及重复性误差小等优点。

• We have also discussed the influence of the variation of the characteristic parameter on the measurement error and shown a design of the network.

  我们又进一步研究了由于网络节点特性变化所引入的误差对检测精度影响，讨论了在一定检测精度要求下，这种光纤补偿网络的优化设计。

• By synthesizing twice MTD results, actual velocity of the target is gained. Relation between pulse duty ratio and velocity measurement error is deduced.

  综合两次MTD结果得到了目标的实际速度，并推导出了脉沖占空比和速度测量误差的关系式。

• Methods Studied factors that affected the occupational stress of doctors in a hospital by means of linear measurement error model.

  方法利用线性测量误差模型对某医院医务人员职业紧张的影响因素进行分析。

• The measurement error of fine wire thermocouples is discussed briefly.

  文中简要分析了细丝热电偶的测量误差。

• Based on the attributes of different errors, the method for transferring miss distance measurement error in servo control system is given.

  在考虑不同误差属性的基础上，给出了脱靶量测量误差在伺服控制系统中的传递方法。

• On the basis of analyzing the operation principle of laser particle sizer, we introduce a method of delamination which is employed to revise the measurement error by high concentration suspension.

  在详细分析激光粒度仪工作原理的基础上，介绍了一种分层方法，用于修正高浓度悬浊液而引起的测量误差。

• The reason that caused measurement error is analyzed deeply. The paper makes use of the neural network to compensate linear structured light measurement system, so improve the measurement precision.

  深入分析了引起系统测量误差的原因，并利用神经网络对线结构光测量系统进行误差补偿，提高了系统的测量精度。

• With this scheme, the automatic positioning and measurement of the axle journal is realized, the manual measurement error is reduced, and the scheme is fairly practical.

  该方案实现了轴颈的自动定位和测量，减小了人工测量误差，实用性较强。

• According to metrological characteristics of diffraction grating, the measurement error models are built up and the equations between installation and measurement errors of grating are deduced.

  根据衍射光栅的计量特点，建立了正交衍射光栅测量误差模型，推导了光栅安装误差与测量误差之间的关系。

• The measurement error of vehicle's attitude caused by the drift of platform reference is also analyzed.

  对由于惯性基準的漂移而引起的载体姿态角的测量误差也进行了分析。

• Conclusion Linear measurement error model is an effective way to cope with measurement error.

  结论线性测量误差模型是分析带有测量误差数据的有效方法。

• Some new models and algorithms are used, they are: zero impedance branch, orthogonal transformations, and measurement error estimation etc.

  采用的新模型与算法有：零阻抗支路处理、正交化算法和量测误差估计等。

• A new optical system is designed for the material surface temperature-measuring device used in laser processing. The measurement error analysis and conclusions are presented.

  通过解决激光加工中材料表面温度测量装置的难点，设计了一套新型光学系统，并给出了测量误差分析及结论。

• Based on the eigenvalue decomposition of the converted measurement error covariance matrix, asymptotic behavior was given about the converted position measurement error.

  基于转换测量误差协方差矩阵的特征值分解，给出了转换位置测量的时间渐近特性。