片语

ternary mechanical structural model三元力学结构模型

mechanical industry model力学模型

mechanical migration model力学迁移模型

Mechanical Calculation Model力学计算模型

interface mechanical constitutive model界面力学本构模型

mechanical structure model力学结构模型

mechanical subelement model力学子单元模型

英汉例句

• three types of four-parameter strength criterion based on new mechanical model are proposed.

  在新的力学模型上建立了三种类型的四参数强度準则。

• mechanical model of plant cell is established.

  建立了植物细胞的力学模型。

• then three-dimensional geological and mechanical model was established, and study of spatial deformation characteristics with flac-3d (fast lagrangian analysis of continua) was detailed.

  并建立了相应的三维地质力学模型，应用flac3d快速拉各朗日差分程序对其空间变形特征进行了详细的分析。

• based on the theory of fracture mechanics, a basic mechanical model of coal cutting is established.

  从断裂力学的理论出发，建立了刀县切削破煤的基本力学模型。

• the paper uses finite element method to calculate the whole reel structure of a ship lift and presents the mechanical model of finite element analysis for the structure as a whole.

  采用有限单元法对升船机卷筒结构进行整体计算，提出了有限元分析的力学模型，对筒壳、幅板的强度及刚度作了全面分析。

• by means of measurement and analysis, the more exact and rational mechanical model of the circuit breaker is presented.

  对该断路器的地震反应的分析需要采用合理的力学模型和适宜的计算方法。

• pass through mechanical model calculate, discover the vault and arch foot part in the tunnel secondary lining thickness is weakness part, so at the design and construction must strengthen these part.

  通过力学模型计算，结构在拱脚与仰拱交接处以及拱顶部位为隧道二次衬砌混凝土结构的薄弱部位，设计和施工时应着重加强。

• the computation examples prove the reasonableness and effectiveness of the mechanical model and the computational methods presented in the paper.

  通过算例，证明本文提出的力学模型与计算方法的合理性与有效性。

• this paper proposes, for the first time, a simplified mechanical model in an attempt to treat the motion of a cell sliding into a two-dimensional slit.

  本文首次提出一个简化的力学模型，试图探讨细胞挤入二维狭缝的运动特性。

• utilized general fem software ansys to establish mechanical model and solve.

  并利用通用有限元软件ansys建立其力学模型并求解。

• a mechanical model of lumbar motion segment was developed with threedimensional finite element method to analyse the stress distribution of lumbar spine in upright posture.

  本文采用三维有限元方法建立了腰椎活动节段的力学模型，对正常人站立时腰椎应力分布情况进行分析。

• due to the difference in stress paths between the loading and unloading conditions, it is unsuitable to apply mechanical model under loading condition to stability of tunnel excavation.

  由于巖体在加载和卸载条件下应力路径的不同，仅采用加载条件下所建立的力学模型来研究隧道的开挖稳定性问题是不适合的。

• in the traditional design and analysis, beam or thin plate is often chosen as the mechanical model for the concrete slab sleeper.

  在传统的设计与计算中，为了简化问题便于工程应用，常选择「梁」、「薄板」作为宽轨枕的力学模型。

• based upon the elasticity theory, a mechanical model for the casing pipe was built and the relationship between residual stress and compression strength was developed by fem.

  运用弹性力学理论，建立石油套管的力学模型，通过有限元计算，得到残余应力与石油套管抗压溃强度之间的关系。

• the reorganization of the system on the basis of the mechanical model is realized by an optimization algorithm.

  建立在力学模型基础上的系统的新结构由优化算法实现。

• based on the theory of the viscoelastic rheological model, the coupled mechanical model of the soft rocks, the concrete sheath and the casing is developed.

  以黏弹性流变模型理论为基础，建立软巖层、水泥环和套管流变耦合的力学模型。

• using the powerful software ansys, the boundary condition and mechanical conditions of supporter was simulated, and a finite element analyzing mechanical model for supporter of rotary kiln was set up.

  通过合理模拟回转窑托轮的边界条件和受力状况，并采用功能强大的ansys软件，建立了回转窑托轮的有限元分析力学模型。

• by setting up the rational mechanical model and measuring the horizontal displacement to calculate the sample angle in composite force test, the problems of the sample angle measurement can be solved.

  在复合力试验中，通过建立合理的力学模型，利用测量水平位移量计算管样角度变化，解决了试样角度无法直接测量的问题。

• as an example of large sized structural component, the mechanical model of load calibration test of an airplane wing was analysed.

  以飞机机翼等大型结构为例，探讨了大型结构部件载荷标定试验的力学模型。

• under the subway vibration mechanical model of the permanent deformation of loess research.

  地铁振动下黄土永久变形力学模型的研究。

• these results can be used as the basis of setting up mechanical model of pur foam plastics.

  这些结果可以作为建立pur泡沫塑料力学模型的基础。

• following the mechanical model of mr smart damper and taking the hefei jade tv tower as the engineering background, this paper studied the control effects under external wind loads.

  依据mr智能阻尼器的力学模型，以合肥翡翠电视塔为工程背景，研究mr智能阻尼器对电视塔结构风振反应的控制效果。

• based on the local, migratory and subsection characteristics of main roof fall of longwall face, the main roof was divided into some plate group, and plate group mechanical model was established.

  针对长壁工作面顶板垮落具有局部、分段、迁移的时空特征， 将长壁工作面采场顶板划分成若干个相互铰接的薄板，建立了薄板组力学模型。

• the simplified mechanical model is proposed with analysis of forces of abutments in this paper.

  通过基牙的受力分析，提出了基牙的简化力学模型。

• a nonlinear mechanical model of grape was constructed.

  建立了葡萄的非线性力学模型。

• by using the mechanical model of continuous variable section cantilever beams, this article derives a practical critical loading formula for calculating the integral stability of pile drivers.

  本文用连续变截面悬臂梁力学模型，并根据能量法原理推导出较符合实际的计算桩架总体失稳的临界载荷公式。