英语释义

1. hardness of a substance (as an alloy) measured by an indenter (as a diamond point) that penetrates microscopic areas

片语

microhardness characteristics显微硬度特征

case microhardness渗碳层硬度

microhardness distribution显微硬度分布

nano microhardness纳米显微硬度

weighted microhardness加权显微硬度

microhardness measurement显微硬度

microhardness tester显微硬度计

Vickers microhardness维氏显微硬度

英汉例句

• it is tested that the depth of laser hardening layer and its microstructure and microhardness varies with the power and scanning speed.

  测定了激光入射功率、扫描速度等工艺参数对灰铸铁表面硬化层深度、组织及显微硬度的影响。

• the results show that the parameters have great effect on microstructure and microhardness of the coatings.

  结果表明，工艺参数对冶金层显微组织及显微硬度有很大的影响。

• as compared to general coating, gradient coating has even more excellent performances in bending strength, bonding strength, thermal shock resistance, microhardness and thermal stress relaxation.

  与一般涂层相比，梯度涂层显示出更为优异的弯曲强度、结合强度、抗热沖击性、显微硬度分布及缓和热应力等性能。

• microstructure and phase structure of light beam cladding layer with iron based self fluxing alloy powder were studied by sem, eds, x ray diffraction, microhardness and rockwell hardness.

  采用sem、eds、x射线衍射及显微硬度和洛氏硬度分析手段研究了铁基自熔合金粉末光束熔覆层的微观组织及其物相组成。

• the microhardness of nitriding layers obtained in a wide range of treatment temperature is 5~6 times higher than that of the substrate.

  可在较宽的温度范围内对该钢进行脉沖直流等离子渗氮，获得表面硬度高于基底5~6倍的渗氮层。

• after laser-remelting the microhardness of laser cladding coating decreases.

  激光重熔后材料表面的显微硬度有所降低。

• the effect of load specimen surface roughness and test deviation amendment on microhardness of aeronautical noble metal (alloy) wires and sheets was studied in this paper.

  研究了加载负荷、试样表面粗糙度及测量偏差修正对航空用贵金属（合金）丝材和薄片显微硬度测量的影响。

• the grinding affected layer of carburized and hardened gears has been studied by means of metalloscopy, microhardness measurment and x-ray diffraction in the paper.

  应用金相法、显微硬度法及x射线衍射法等手段对渗碳淬火齿轮磨削变质层进行了检测与分析。

• microhardness testing during aging treatment in high purity steel bearing copper was carried out.

  对经时效处理后的含铜高纯钢进行了显微硬度测试。

• the phase composition and the microhardness of the diffusion layer were analyzed by x-ray diffraction and microhardness apparatus .

  实验还通过x射线衍射仪和显微硬度测试仪分析了渗层的物相结构与显微硬度。

• the results show that, microhardness of friction component plays a very important role on friction coefficient and its stability of the friction material.

  结果表明摩擦组元的显微硬度对摩擦因数和摩擦因数稳定度影响显着。

• the microhardness and surface roughness of specimens before and after shot peening was studied and analysed.

  分析研究了喷丸强化处理前后的显微硬度和表面粗糙度。

• wang, r. , and s. weiner. 「 human root dentin: structural anisotropy and vickers microhardness isotropy. 」 connect tissue res. 39, 4 (1998): 269-79.

  人类牙根：结构非均向性与维克微硬度等向性〉刊于《连结组织研究》39，4 （1998）：269-79。

• these results indicate that the microhardness of crystals depends not only on the crystal structure and lattice energy but also on temperature.

  最后指出晶体硬度不仅与晶体的结构、晶格能有关，而且也与温度的影响有关。

• in this paper the mechanism and process of light beam surface alloying were investigated by sem, x-ray diffraction, optical microscope, microhardness etc.

  采用sem、x射线、光学显微镜、显微硬度计等手段研究了高能密度光束表面合金化的机理和工艺。

• employed by optical microscope, scanning electron microscope, microhardness tester and x ray diffraction instrument, the isothermal decomposition process of high nitrogen austenite was investigated.

  利用光学显微镜、扫描电镜、显微硬度计及x射线衍射仪分析了高氮奥氏体的等温分解过程。

• the results show that multi-stage aging treatment can increase wear resistance, corrosion resistance and electrical properties of nbc alloy, but microhardness has not changing apparently.

  结果表明，nbc合金经过分级时效处理后，耐磨性、耐腐蚀性和电导率有所提高，而显微硬度无明显变化；

• the microhardness of jcw-s-am coatings prepared by high velocity electric arc spraying on conditions of different process parameters was tested by hardometer.

  采用超音速电弧喷涂设备在不同工艺参数条件下制备jcw-s-am涂层，利用显微硬度计测定各种涂层的显微硬度。

• as early as 1984, the status of our plant veteran developed standards shuigen microhardness block, by the experts, the indicators have reached international standards.

  早在1984年我厂元老况水根研发的标準显微硬度块，经有关专家鑒定，各项指标均达到国际水平。

• the depth and microhardness distribution of alumetizing layer obtained on different technical conditions were measured.

  测定了不同工艺条件下获得的浸渗层深度和浸渗层显微硬度的分布。

• surface modification treatment of pure magnesium by solid diffusion zinc treatment is conducted, and the microstructure, microhardness and corrosion behavior of alloying layer are investigated.

  采用固态扩渗锌粉方法，对纯镁进行表面合金化改性工艺处理，研究合金层组织结构、硬度及其腐蚀行为。