片语

Molten pool level熔池液位

cooking food molten pool沸腾状熔池

molten weld pool焊接熔池

molten pool stirring熔池搅拌

Molten Pool Flow熔池流动

molten slag pool渣池

boiling g molten pool沸腾状溶池

dimension of molten pool熔池尺寸

英汉例句

• It was shown that new type metal delivery system can make molten steel distribute uniformly in the molten pool and is favorable for strip shell to solidify uniformly.

  结果表明，新型布流系统可使钢液在熔池内均匀分布，有利于薄带坯的均匀凝固。

• The model can be used to predict metal molten pool can guide the practical production.

  运用此模型可预报金属熔池状况，指导实际生产。

• The results showed that the backflow occurred at the center region of molten pool by the effects of fluid viscosity and the rollers extrusion.

  研究结果表明，由于液体的黏性力和轧辊的挤压作用，在熔池芯部区域会产生回流现象。

• The forces applied on the molten pool at the cathode surface under the action of an external magnetic field during vacuum arc coating are analyzed.

  分析了在外加磁场作用下，真空电弧镀膜中阴极靶面液池的受力情况，导出了液滴喷溅特性受磁场影响的关系式。

• It is necessary to extract molten pool geometrical parameters in real time or to extract back bead width off-line either in seam tracking or in penetration control.

  不论熔透控制还是焊缝跟蹤，都需要实时或离线提取焊接熔池正面或反面的几何参数。

• The key point of designing coaxial nozzle is how to acquire the steady airstream, which can be used to control the plasma and protect the molten pool at high temperature at the same time.

  同轴喷嘴设计的关键问题在于如何获得稳定均匀的同轴气流，使气流在控制等离子体的同时，又能为钛合金高温熔池提供保护。

• And this model can be used to predict the status of the metal molten pool and instruct practice production.

  运用此模型可预报金属熔池状况，指导实际生产。

• Plasma transferred arc produces the induced electromagnetic field that makes liquid metal convect in molten pool in the surface metallurgical course.

  在表面冶金过程中等离子束产生感生磁场，使熔池内液态金属产生对流运动。

• By increasing the weld heat input, the distribution of martensite becomes more dispersive and glomerate due to the molten pool stiring, the welding stress and the burning loss of alloy elements.

  随着焊接热输入量的增加，由于熔池搅拌、焊接应力、合金元素烧损等原因，马氏体的分布更加散乱和密集；

• The new method involves passing a current through a molten pool of iron oxide, which drives off the originally sought-after oxygen.

  新方法的步骤则包括向熔炉里的氧化铁通电，从而释放原本就炙手可热的氧气。

• The result shows that the temperatures of molten pool surface and bottom are lower than those ones in arc welding. This is main cause of formation of low dilution rate.

  结果表明，熔池表面和底部的温度都低于电弧焊，这是造成低稀释率的根本原因；

• At quasi - state stage, the depth and radius of laser pool have small changes, but the highest surface temperature and velocity of molten pool decease rapidly.

  在凝固準稳态阶段，熔池熔深和半径变化较小，但表面最高温度、熔池流速急剧减小；凝固加速阶段则反之。

• Experimental results show that the crystallization of weld pool is in the motion state, the columnar crystal in welding line is formed on the wall of molten pool and grows from the edge to the center.

  结果表明：复合焊接中，焊缝熔池在运动状态下结晶，焊缝在熔池壁处形成的柱状晶，由池壁向中心生长。

• The main feature of the device is able to observe arc and molten pool directly in coaxial direction so that the welding process is easily controlled and alignment of weld can be warranted.

  其装置特点是能够轴向直接观察电弧和熔池状态，从而便于控制焊接过程，保证焊缝的对中性。

• The center region backflow would stir the molten pool and reduce the temperature to some extent which would make the temperature field and solute field uniform and steady.

  芯部回流可在一定程度上搅动熔池并促使芯部温度降低，有利于促使温度场和溶质场均匀稳定。

• The depth of the metal molten pool influences the crystallization of castings so much as to influence the quality of castings in the ESR.

  电渣熔铸过程中，金属熔池深度直接影响熔铸件的结晶，从而影响钢锭的质量。

• The change of molten pool temperature of different layers was measured, and the Metallographic and Microstructures in combined interface were analyzed.

  在单道多层熔覆中测量了熔覆不同层时熔池温度的变化，分析了结合面的金相和熔覆层的组织结构。

• Two kinds of banded structure caused by convection and unstable moving of the worktable have been observed on the surface of the molten pool and in the melted region.

  熔池中存在的对流和激光扫描过程中工作台运动的不稳定造成了熔池表面波纹状组织和熔池中三维条带状组织的出现。

• The plasma cloud charge sensor was applied to detect the status of keyhole molten pool during pulsed plasma arc welding, furthermore, the detected signals were studied.

  将等离子云传感器应用于脉沖等离子弧焊穿孔熔池小孔状态检测，并对检测信号的波形特征做了深入研究。

• The reactance restraint type of furnace should take method of operation to make molten pool power and active power maximum.

  电抗约束型炉子应采用使熔池功率或有功功率最大的方式运行。

• The influence of laser power, scanning speed, powder feed rate, spot diameter and preheating on the temperature of molten pool were revealed in the process of single-pass cladding.

  在单道熔覆中通过跟蹤测量研究了激光功率、扫描速度、送粉速率、光斑直径和基体预热温度对熔池温度的影响规律。

• Weld spatter consists of particles of metal unintentionally ejected from the molten pool during welding and deposited on the surface of base or weld metal.

  焊接溅落包括无意地从熔融池中溅出的金属颗粒并落到了母体金属或焊缝金属的表面。

• During laser processing, the heating and cooling process of laser molten pool can be acquired by the numeric model.

  通过该计算模型，可以掌握激光加工过程中连续移动激光熔池的加热和冷却规律。