片语

indirect tensile stiffness modulus间接拉伸模量

complex tensile creep modulus复变张力潜变模数

tensile elastic modulus拉伸弹性模量

Tensile strength modulus拉伸强度模数

tensile relaxation modulus拉伸松弛模数

flexural tensile elastic modulus弯拉弹性模量

rubbery tensile modulus橡胶态拉伸模量

tensile cteep modulus拉伸蠕变模量

Tensile e modulus伸张模数

英汉例句

• an analytical algorithm to estimate the tensile modulus of brazilian disk splitting tests is presented.

  提出巴西圆盘劈裂试验中拉伸模量的解析算法。

• in this paper, the relation of tensile strength, tensile modulus and breaking elongation of unsaturated polyester casting matrix cured at room temperature to curing degree was discussed.

  本文讨论了常温固化不饱和聚酯树脂浇涛体的拉伸强度、拉伸模量、断裂延伸率与固化度之间的关系。

• in the bulk system, tensile strength, tensile modulus and impact strength are improved by 32.2%, 60.3% and 68.6%, respectively, without the loss of light transmittance.

  而本体法复合材料的拉伸强度、拉伸模量及沖击强度值最大分别提高了32.2％、60.3％和68.6％，而透光性能基本未受影响。

• this article introduces a method to determine the plastic membrane tensile modulus by using a normal mart electron tensile testing machine and computers.

  文章介绍了一种利用普通的智能电子拉力试验机配以计算机来计算塑料薄膜拉伸弹性模量的方法。

• the tensile modulus approximately equal to the compressive modulus of elasticity within the proportional limit.

  拉伸载荷模量约等于比例极限内的弹性模量。

• the effects of glass bead content and its size on the elastic tensile modulus (e) of the filled low density polyethylene (ldpe) composites are studied.

  研究了填充低密度聚乙烯中玻璃微珠含量及其大小对复合体系拉伸弹性模量e的影响。

• tensile modulus and yield stress of blends increase with concentration of pmma.

  结果表明，共混物的拉伸模量、屈服应力随pmma含量增加略有增大。

• the effects of the content and dispersion of carbon nanotubes on the tensile strength, tensile modulus and ratio of elongation of the nanocomposites were studied.

  研究了碳纳米管的加入量与分散程度对复合材料的拉伸强度、拉伸模量、断裂伸长率的影响。

• with vp-501 content increasing, the fracture toughness was increased, while the tensile modulus was decreased at both rt and 77 k.

  随着vp-501含量的增加，体系在rt和77k下的断裂韧性增加了，然而其拉伸模量降低了。

• the results show that tensile strength and tensile modulus increase and cold-resisting property descends with temperature dropping.

  结果表明，随着温度的降低，该橡胶的拉伸强度、拉伸模量升高，耐寒性下降；

• the tensile modulus showed a negligible change with thermal oxidation temperature.

  模量随热氧化温度变化不明显。

• the tensile strength, bending strength, impact strength, tensile modulus of elasticity and bending modulus of elasticity were determined.

  测试了塑木板材的拉伸强度、弯曲强度、沖击强度、拉伸弹性模量、弯曲弹性模量等力学性能；

• it is shown from the numerical results that the ratio of compressive modulus to tensile modulus will greatly affect the elastic characteristic values, internal forces.

  为此，合理设计材料的拉压模量比值，可以显着的改变地基梁的弹性特征值、内力及挠度值。