片语

test specimen tube试样筒

test sample[试验] 试样；试棒

wing shaped test specimen翼形试样

Test control specimen染色坚牢度试验标準样布

fatigue test specimen疲劳试验件

parent metal test specimen母体金属试样

sand test specimen型砂试样

tensile test specimen拉伸试样

tongue shaped test specimen舌形试样

sample bar试样

compression molding test specimen压塑试样

英汉例句

• but considers from the packing cost aspect the d test specimen both to be possible to save the cost and to be able to achieve to the glass cushion protective function.

  但从包装成本方面考虑，d试样既可节省成本又能达到对玻璃的缓沖保护作用。

• in the first place, it is pointed out defects of national standard metal molding tension test specimen for casting aluminum alloy in this paper.

  指出了铸造铝合金国家标準金属型抗拉试样在实际生产过程中存在的问题。

• both types of specimen, three-point bending beam with notch and wedge splitting test specimen are applied to measure the fracture-resistance properties of fiber reinforced concrete in early age.

  采用三点弯曲切口梁和楔入劈裂紧凑拉伸两种试验模型，测试早龄期阶段钢纤维混凝土材料的抗裂性能；

• the test specimen may be titrated with the reagent directly, or the analysis may be carried out by a residual titration procedure.

  待测样品可能会被卡尔试剂直接滴定，或者采用回滴定法完成分析。

• maximum impact force is the greatest impact force (in inch-lbs) applied that did not cause visible damage or deformation to the test specimen surface.

  最大撞击力是指应用在测试样品表面上但没有出现肉眼可观测到损伤或变形的最大撞击力（单位：英寸磅）。

• if the test specimen is in the form of large crystals, reduce the particle size to about 2 mm by quickly crushing.

  如果样品的是比较大的晶体，需要用高速粉碎机粉碎到约2mm左右的颗粒，方可进行检测。

• charpy impact test (v gap): the specified height of pendulum of the one-time blow to v notched specimens in beam state, test specimen is broken by the impact absorbing energy.

  夏比（v型缺口）沖击试验：用规定高度的摆锤对处于简支梁状态的v型缺口试样进行一次性打击，测量试样折断时沖击吸收功的试验。

• the ratio of the two specimens photoacoustic signals is the devices output, and it can be used to study the property of the test specimen .

  利用这一比值，可以由参考样品的性能参数方便地求出待测样品的相关性能参数。

• some factors of influencing representativity of concrete test specimen are discussed, and the improving measures are presented in this paper.

  分析了影响砼试件强度代表性的几种原因并提出改进措施。

• test specimen has been designed and manufactured and a counter-rotating turbine test rig has also been constructed.

  设计制造出了试验件，建立了对转涡轮试验台。

• test specimen shall be dissolved with acid. the solution shall be used for analyzing calcium and barium.

  试样用酸溶解后，取所制溶液分析钙、钡。

• the influence of seams on the behaviour of fabrics can be determined by this method, the seam being positioned within the test specimen so as to be subjected to the test flame.

  老态龙钟的影响，对这种行为可以确定的织物用这种方法、拼缝被放置在测试样本以受试片被火焰点燃。

• in the desiccant method the test specimen is sealed to the open mouth of a test dish containing a desiccant, and the assembly placed in a controlled atmosphere.

  在增重法中，试样被密封在装有干燥剂的透湿杯杯口处，然后将整套透湿杯组件放在控制环境中。

• it is put forward that the analysis method of fracture surface of metallic tension test specimen is available.

  提出的金属拉伸试样断口分析方法是可行的。

• the effect of discriminating different beef-producing areas in small geographic scope using beef tail hair as test specimen is studied. guanzhong area of shanxi province is chosen as the sampled area.

  接着以陜西省关中地区为例，研究了利用牛尾毛作为试验样品进行小地理范围牛肉产区划分的可行性。

• the spectral reflectance of each test specimen is measured in situ before and after exposures.

  在辐照前后对每一个试样的光谱反射系数进行了原位测量。

• figure 4 shows the instrumentation of the test specimen .

  图4示出了试验样本的仪器。

• p98 data for stress-strain diagrams are usually obtained by applying an axial load to a test specimen and measuring the load and deformation simultaneously.

  通常，对试件施加平轴荷载，并且同时测量荷载和变形，这样就获得了应力—应变图的数据。

• if we will not reach that switch point after that time the test specimen will be rated bad.

  如果我们在那段时间后没有达到设定值，试样就被认定是不合格。

• secondly, it is introduced that a new applied standard metal mold tension test specimen is designed.

  介绍了一种新的实用标準金属型抗拉试样。

• test specimen shall be dissolved with alkali, then treated with nitric acid.

  试样用堿溶解后，用硝酸酸化。

• by use of the method of welding thermal simulation, the morphology in haz was simulated and the post-weld heat treatment under different tempering parameter to the test specimen was carried out.

  采用焊接热模拟的方法，模拟haz粗晶区组织，并在不同回火参数下对试样进行焊后热处理。

• through to the dynamic cushion performance of liner and the vibration transmission rate comparison, may know the e test specimen's cushion performance to be best, the d test specimen is next.

  通过对衬垫的动态缓沖性能和振动传递率的比较，可知e试样的缓沖性能最好，d试样次之。