英语释义

1. stress in a body or structure due to inequalities of temperature

片语

thermal-stress model热应力模型

thermal shock stress热沖击应力

thermal electrical stress热电应力

Thermal Creep Stress温度徐变应力

thermal load[动力] 热负荷；[力] 热应力

the thermal shrinking stress热收缩应力

thermal internal stress残余热应力

temperature stress温度应力，温差应力；热应力

thermal contract stress温缩应力

thermal shrinkage stress热收缩应力

Thermal expansion stress range热胀应力范围

英汉例句

• the equation on critical stress of matrix cracking that could consider the effect of interface layer and thermal stress can be obtained.

  在此基础上建立了可以考虑界面层和热应力影响的基体开裂临界应力求解方程。

• in this research work, the thermal elastic-plastic method is used to analyze the dynamic thermal stress in the stress-frame specimen during its solidification and cooling process.

  本研究用热弹塑性方法分析铸造应力框自凝固到冷却过程动态热应力。

• in the processes of aquifer thermal energy storage, the variation of temperature in solid matrix will bring about thermal stress and result in the change of effective stress.

  含水层储能过程中回灌水的温度与背景温度不同，固体骨架温度变化产生的热应力将导致有效应力的变化。

• the thermal stress of rcc dam is different from concrete dams, and in order to get correct results, these different characteristics must be considered.

  碾压混凝土坝的温度应力有它不同于常规混凝土坝的特点，必须考虑这些特点，才能得到正确的结论。

• coke tower is major equipment in delay-coking unit. but due to the severe service conditions, coke tower is loaded recling thermal stress and pressure.

  焦炭塔是延迟焦化装置中的关键设备之一，由于操作条件苛刻，使焦炭塔受到循环往复的热应力和内压的作用。

• it was shown that the dynamic effect of the temperature and thermal stress of piston must be considered during thermal shock.

  计算结果表明：活塞在热沖击期间表现的温度及热应力的动力学效应是必须加以考虑的。

• the result shows that the plastic strain at the heel region induced by wire bonding process, molding process and the thermal stress and strain in solder reflow are the main causes of heel crack.

  结果显示由于引线键合工艺、注塑工艺以及回流焊中封装体各部分不同的热膨胀系数引起的热应力和塑性变形是产生引脚跟断裂的主要因素。

• an analogy method to solve thermal stress problem and lateral bending problem in ortho-anisotropic mediums is presented in this paper.

  介绍一种用于求解正交各向异性介质中平面热应力问题与横向板弯问题的比拟方法。

• according to the trial, we use finite element analysis program to conduct temperature field and thermal stress analysis of the pier under sunshine, and compared the outcome with experimental results.

  根据试验采用有限元分析程序，进行日照作用下桥墩的温度场和温度应力分析，并与实验结果进行对比。

• the transition conditions from corrosion fatigue to scc have been discussed in terms of the cycling thermal stress and its stress ratio.

  在本文中，从循环热应力及其应力比的角度，讨论了从腐蚀疲劳向应力腐蚀断裂过渡的条件。

• the temperature field is exerted to the finite element model as the body load to calculate the thermal stress of the substrate model utilizing the ansys.

  并将计算所得的温度场作为体载荷施加到有限元模型，利用ansys软件对基板模型进行了热应力的计算分析。

• the thermal stress distribution of the stainless steel lined composite steel pipe prepared by centrifugal-shs process was calculated by the finite element method under thermoelastic assumption.

  用有限元方法计算了铝热离心法制备不锈钢内衬复合钢管过程中的残余热应力分布。

• it tells the changing tendency of is contrary for work life of rolling stress and thermal stress roll rings under given assembly stress.

  表明在一定的装配应力下，为保证辊环的使用寿命，轧制应力与热应力值的变化趋势相反。

• this conclusion is some value to decrease thermal stress of cooling tubes and protect the sealing.

  本文的结论对于减小冷却管热应力，防止凝汽器密封破坏，具有参考价值。

• all above conclusions may be used to investigate the two-dimension thermal stress with complicated boundary conditions and the three-dimension thermal stress problems furthermore.

  本文的研究成果为进一步研究复杂边界条件下的平面热应力问题及三维热应力问题提供了基础。

• meanwhile, the fillet geometry has played an important role on this thermal stress distribution.

  同时，钎缝圆角几何形状对这一热应力分布有重要影响。

• the ion-implantation damage defects and thermal stress during quenching step are responsible for the formation of dislocations.

  位错的形成与离子注入引进的损伤和淬火过程中的热应力有关。

• the stress of anodic bonding is analysed and the math model of no match thermal stress about anodic bonded elastic diaphragm is built.

  通过对静电封接结构的受力分析，建立了静电封接后弹性膜片的热失配应力数学模型。

• the results of thermal stress analysis lay the solid foundation for design and improvement for gravity supports system for iter .

  热应力分析的结果为iter重力支撑系统的设计或改进提供了可靠的理论依据。

• the temperature field and the thermal stress state of multilayer wall pipe have a heavy effect on the reliability of structure.

  多层圆管结构在不稳定导热过程中的温度场及其热应力状态，关系到结构的安全可靠性。