片语

allowable crushing stress容许压碎应力

allowable e stress容许应力

admissible stress容许应力，许用应力

allowable flange stress intensity法兰许用应力强度

allowable twisting stress许用扭转应力

allowable compressive stress容许压缩应力

allowable contact stress index容许接触应力指数

Allowable Bearing Stress容许承载应力

allowable design stress设计许用应力

the allowable tensile stress脱空应力

英汉例句

• at last, under the allowable stress with ansys to optimize the design of the final model and gain a new kind of horn with resonance of 12.35.

  最后借助ansys优化设计模块进行仿真实验，在材料许用应力下对变幅桿进行优化设计，获得了谐振比达12.35的新型变幅桿。

• the many indefinite exists in the design parameters and influence factors of the working stress and allowable stress of the k - h three - ring planetary reductor.

  三环行星传动设计中，在工作应力、许用应力的设计参数和影响因素中存在着许多不确定性。

• strength design values may be converted to allowable stress design values.

  设计要求、强度设计值可转换为许用应力设计值。

• the development of otc steel structure design from definite allowable stress method into probability-reliability method is considered as a significant step forward in design theory.

  桥式起重机钢结构从定值许用应力法发展到概率可靠性设计法是设计理论的重大发展。

• the allowable stress number, load, geometry parameters and life have the most significant effects on pitting resistance rating results;

  试验齿轮的应力修正系数、载荷和几何参数对弯曲强度计算结果的影响较大。

• properties of main structure components were specified as the design variables, while the allowable stress and displacement were considered as constraints.

  通过分析，获得了承载结构主要梁件和板材的优化设计参数。

• the allowable stress of the pipe material shall be chosen from the data of gb 50316 design specification for industrial metal piping.

  管子材料的许用应力可按gb50316《工业金属管道设计规范》中的数据选用。

• according with the allowable stress design theory, the wind loads and load-carrying capacity of antenna struts are calculated, and their inter forces are analyzed.

  根据容许应力设计理论，对天线撑桿的风荷载和承载能力进行结构计算，并对天线撑桿进行内力分析。

• this paper describes the selection of allowable stress about aluminum material 1050a and 5083 which used in stress analysis intensity calculation of aluminum railway tank.

  本文主要描述了铝材1050a和5083在铝制铁道罐车应力分析强度计算中许用应力的确定方法。

• the analysis results of the finite element method show that the maximum mises stress of the axle housing is less than the allowable stress value.

  通过强度试验结果与理论分析数据相比发现两者之间误差较小，验证了有限元模型建立的合理性。

• the underground penstock for the husonghe hydroelectric power station was designed using the calculation method of raising the allowable stress as an open conduit;

  户宋河电站地下埋管主管的设计，采用按明管设计提高允许应力的计算方法；

• minimum wall thickness and allowable stress conforms to ansi b16.34.

  最小壁厚和安全应力符合美国国家标準化组织ansib16.34标準。

• allowable stress is widely employed in china to verify the strength in the evaluation of the bearing capacity of arch ribs of steel-tube reinforced concrete.

  目前国内钢管混凝土拱桥设计、钢管混凝土拱肋承载力的评定，大多采用容许应力法进行强度验算。

• the allowable stress is the value of the determined basic allowable stress of the piping material multiplied by a quality factor.

  而管道许用应力是在确定了管道材料的基本许用应力后，乘以质量系数所得的值。

• then, suggested values of the allowable stress ranges corresponding to different target fatigue lives under the specified ensuring probability were proposed for corroded steel bars.

  经统计回归，建立了考虑锈蚀率影响的锈蚀钢筋疲劳曲线方程，给出了不同保证率、不同预期疲劳寿命下自然锈蚀钢筋容许应力范围的建议值。

• the many indefinite exists in the design parameters and influence factors of the working stress and allowable stress of the roller movable teeth drive.

  滚子活齿传动设计中，在工作应力、许用应力的设计参数和影响因素中存在着许多不确定性。

• by means of satisfying stability condition and adopting allowable stress range reducing factor, both the plastic fatigue and elastic fatigue can be prevented by the secondary stress check condition.

  通过满足安定性条件和引入许用应力范围减小系数，二次应力的校核条件可同时防止塑性疲劳和弹性疲劳破坏。

• in this case allowable stress of imported material shall be those for equivalent material in gb150-1998 as follows.

  在此情况下，进口材料的允许应力与gb150-1998中的相当材料相同。

• selection basis and method on allowable contact stress of rolling ball-socket nozzle were described. based on empirical formula and test data, several factors affecting allowable stress were analyzed.

  叙述了滚动球窝喷管在设计中许用接触应力的选择依据及方法，并根据以往的经验公式及其试验数据对影响许用接触应力的几个因素进行了分析。

• bridges of this kind are designed according to fully prestressed concrete theory, and tensile stress is allowed to exceed allowable stress during construction and service.

  这类桥梁在设计计算过程中均是按照全预应力混凝土结构进行设计的，施工和运营中任何截面混凝土拉应力均不允许超过允许应力值。

• themaxium range of allowable stress under different reliability is given.

  文中还给出了对应于不同可靠度下的最大容许应力幅值。

• some datum, for example safety factor and allowable stress are put forward based on production practice.

  提出的设计数据如安全系数、许用应力均根据生产实践的应用所确定。

• the results indicate that it is conservative to design cfst arch bridges by using allowable stress method in steel tube, and that it is reasonable to use limit state method.

  数例表明，目前广泛应用钢管应力控制cfst的设计过于保守，文中方法似更合理。