片语

System boot loader系统引导程序

Unlock the boot loader解锁

System boot loader file系统引导加载程序文件

boot loader mode引导模式

cold boot loader冷启动加载器

Lilo Boot Loader选择

Master Boot LoaDeR启动不同分区上各种操作系统

Boot Loader Security启动加载器的安全

英汉例句

• If you change your LILO config file, you have to rewrite the LILO stage one boot loader to the MBR.

  如果修改了LILO配置文件，必须将LILO第一阶段引导加载程序重写到MBR。

• If you have multiple operating systems installed on your server, you need to select which one you want from the boot loader menu.

  如果服务器中安装了多个操作系统，您需要从引导加载程序菜单中选择需要引导的操作系统。

• LI: The second stage boot loader has been loaded.

  LI：第二阶段引导加载程序已经被加载。

• It does this by making the two-stage boot loader into a three-stage boot loader.

  它是通过将两阶段的引导加载程序转换成三阶段的引导加载程序来实现这项功能的。

• This boot loader is less than 512 bytes in length (a single sector), and its job is to load the second-stage boot loader.

  这个引导加载程序在大小上小于512字节(一个扇区)，其作用是加载第二阶段的引导加载程序。

• The screen that appears prompts you to customize the boot loader configuration, as shown in Figure 12.

  显示的屏幕会提示您对引导加载程序配置进行定制，如图12所示。

• The second stage boot loader is the real meat of the boot loader; many consider it the only real part of the boot loader.

  第二阶段引导加载程序是引导加载程序的主体；很多人认为这才是引导加载程序的真正部分。

• The first-stage boot loader scans the table, looking for the active partition; when the loader locates the partition, it loads the second-stage boot loader into RAM and invokes it.

  第一阶段的引导加载程序对表进行扫描，查找活动分区；当加载程序找到分区时，就将第二阶段的引导加载程序加载到RAM中并调用它。

• Select the appropriate boot loader configuration, as shown in Figure 8.

  选择适当的引导加载程序配置，如图8所示。

• Primary boot loaders are where the first stage of the boot loader is installed on the MBR (per the previous description).

  主引导程序是安装在MBR上的第一阶段引导加载程序(见先前的描述)。

• When a boot device is found, the first-stage boot loader is loaded into RAM and executed.

  当找到一个引导设备之后，第一阶段的引导加载程序就被装入RAM并执行。

• Set the boot loader password, as shown in Figure 10.

  设置引导加载程序密码，如图10所示。

• The primary boot loader that resides in the MBR is a 512-byte image containing both program code and a small partition table (see Figure 2).

  MBR中的主引导加载程序是一个 512字节大小的映像，其中包含程序代码和一个小分区表（参见图2）。

• You can interact with the boot loader to select which of several possible configurations to boot.

  可以与启动加载程序交互，选择引导哪个配置。

• You should be able to use your chosen boot loader to boot normally as described above.

  您应该能够使用所选的启动加载程序按前面描述的方式执行引导。

• A separate boot loader must then be installed into the MBR and configured to pass control to the secondary boot loader.

  必须在mbr上安装单独的引导加载程序，并配置它将控制权转交给二级引导加载程序。

• Because most disk devices use a sector size of 512 bytes, the first-stage boot loader code must be very small.

  由于大多数磁盘设备扇区大小为512字节，因此第一步引导加载程序代码都很小。

• When the stage 1.5 boot loader is loaded and running, the stage 2 boot loader can be loaded.

  当阶段1.5的引导加载程序被加载并运行时，阶段2的引导加载程序就可以进行加载了。

• The first step of the boot process is the boot loader shown in Figure 1.

  引导过程的第一个步骤是图1 所示的引导载入程序。

• The installation process for your distribution will probably give you a choice of which boot loader to set up.

  您的发行版的安装过程可能支持选择设置哪个启动加载程序。

• Before I discuss booting up your new drive, a little boot loader theory is required.

  在讨论引导新的驱动器之前，需要了解一些引导加载程序理论。