片语

SIMCO HBA离子风枪与高压电源

hba c糖化血红蛋白

HbA levelHbA定量

HBA Graphics室内标识顾问

hba cardhba卡

hba卡hba card

HbA 1c糖化血红蛋白

HBA Program年哈佛北京书院

iSCSI HBA主机总线适配器

英汉例句

• MSJ is used for configuration of the Qlogic adapters, failover, and multipathing, which is described in detail under HBA configuration.

  MSJ用于Qlogic适配器、故障恢复和多路径等配置，这将在HBA配置一节中详细进行介绍。

• See the SAN infrastructure and the HBA configuration sections in Part 4 of the series for details about these steps.

  有关这些步骤的详细信息，请参看第4部分的SAN架构一节和HBA配置的相关章节。

• Had engaged in Wilson, HBA and other companies design work.

  曾在威尔逊、HBA等公司从事设计工作。

• 1b: 32:04:82: b7 (Your server HBA port 1 WWPN).

  1b： 32：04： 82：b7(服务器hba端口1WWPN)。

• You need to make a switch zone for each path so your server HBA port can reach the DS8000 IO port.

  每条路径都需要一个切换区域，以便您的服务器hba端口能够到达DS8000io端口。

• The path from the system processor/memory/OS/App to the HBA contains only the read data block.

  在从系统处理器/内存/操作系统/应用程序到HBA 的路径上，只传输读取数据块。

• Result: The fibre channel HBA hot swap is now complete.

  结果：光纤通道HBA卡更换完成。

• The request is passed from the cluster disk driver to the Microsoft storage driver stack and finally to the driver specific to the HBA that communicates to the disks.

  请求从集群磁盘驱动传递到微软存储驱动栈，并最终传递到与磁盘通讯的那个总线适配器。

• For the DS4800 storage server, IBM recommends and provides the RDAC driver to use on top of the HBA (host bust adapter) driver.

  对于DS4800存储服务器，IBM推荐并提供了RDAC驱动程序，该驱动程序可在HBA (hostbustadapter)驱动程序上使用。

• The HBA 1000 was designed to scale, connecting up to 16 storage devices natively, or scaling even further with an expander.

  将HBA 1000被设计成比例的，最多可连接16个存储设备本身，或与膨胀甚至进一步缩放。

• It「s like setting up another HBA port, so just follow the same steps.

  这就跟设置hba端口一样，因此按上述步骤进行即可。

• Host connect is used to map your server」s HBA WWPN to one dedicated volume group on the DS8000 so that your server can access all volumes in this dedicated volume group. The command goes like this.

  使用主机连接将服务器的HBAWWPN映射到DS8000上一个专用卷组，以便服务器可以在专用卷组中访问所有卷。

• Defining HBA configuration on storage servers.

  在存储服务上定义HBA配置。

• This zoning removes unnecessary PLOGI activity from host to host, as well as removing the risk of problems caused by a faulty HBA affecting others.

  这种分区消除了主机间不必要的PLOGI动作，也消除了故障的HBA对其他HBA产生影响的风险。

• At the switch fabric, I put the first WWPN of the host HBA into one zone, along with a WWPN of storage controller a.

  在switchfabric，我将主机hba的第一个WWPN与存储控制器a的一个WWPN一起放入一个区域。

• Prior to forming BUZ Design, J Lee was Managing Director of HBA in HK, where she designed and directed many prestigious hotel projects.

  在创立BUZ室内设计顾问有限公司之前，罗颖佳是香港HBA有限公司的董事总经理，设计和指导过许多着名的酒店项目。

• 1b: 32:24:82: b7 (Your server HBA port 2 WWPN).

  1b： 32：24： 82：b7(服务器hba端口2WWPN)。

• I have an IBM x3550 server with an HBA card that has two FC ports.

  我有一个IBMx3550服务器，它有一个带2个pc端口的hba卡。

• If you use an HBA from another vendor, refer to their documentation for the correct setting.

  如果您使用其他供应商的HBA，请参考相应文档获得正确的设置。

• In this configuration, you have used zones where each HBA on each host sees only one controller on the relevant DS4500.

  在本例的配置中，曾用到过专区，在这些专区中，每个主机上的每个HBA只能看到相关DS4500上的一个控制器。

• In this case, put all other SCSI adapters drivers (like the Qlogic HBA driver qla2xxx.ko) after the sas adapter driver mptsas.ko.

  在本例中，将所有其他SCS i适配器驱动程序(如qlogicHBA驱动程序qla2xxx . ko)放在sas适配器驱动程序mptsas . ko之后。

• After selecting a boot device for each HBA or HBA port, you're ready to insert the Linux installation media and start the OS installation.

  为每个hba或hba端口选择根设备之后，可以插入Linux安装媒体并开始安装操作系统了。

• The multipath driver is analogous to the brain, and the HBA driver is analogous to the arms and legs.

  多路驱动程序就像是大脑，而HBA驱动程序就像是胳膊和腿。

• You can select the first HBA port, which will bring you to the Fast! UTIL Options page, shown in Figure 10.

  您可以首先选择hba端口，然后将出现Fast ！UT ILOptions页面，如图10所示。

• After you add back the disabled path, you need to run multipath -v0 to add it back to the path list after your HBA driver finds a new enabled path.

  重新添加了禁用路径之后，您需要在HBA驱动器发现新的启用路径后运行multipath -v0将其添加回路径列表。

• Set up HBA to enable the BIOS and select the boot device from DS8000.

  将HBA设置为支持BIOS，并选择从DS8000启动设备。