片语

ultimate stress极限应力；最大应力

maximum horizontal stress最大水平主应力

maximum shear stress[力] 最大剪应力，最大切胁强

Maximum friction stress最大摩擦应力

the maximum tangent stress最大切向应力

Maximum allowable stress values许用应力

Generalized Maximum Tensile Stress广义最大拉应力

the Maximum Shear Stress或最大剪应力

maximum tensile stress theory最大拉应力理论

英汉例句

• if the structural element of the stent is symmetrical, the uniform stress appears by force, furthermore, the stress concentration is avoided effectively, and the maximum stress decreases obviously.

  支架单元结构的均匀，可使得支架受力时应力分布均匀，且有效避免应力集中现象，其应力最大值明显减小；

• according to the maximum stress strength criterion, the burst pressure formula for the single spiral and the spiral with hoop filament-wound toroidal pressure vessel were obtained.

  利用最大应力强度準则，得到了单一螺旋缠绕及螺旋加环向缠绕圆环压力容器爆破压强的计算式。

• therefore, applying optimum weighted composite prediction model to predict the maximum stress is feasible, it provide a more practical new mean for engineering.

  因此，用最优加权组合预测模型来推求应力集中区的最大应力，是工程测试数据处理的一种比较实用的新方法。

• results under every load, the maximum stress of femoral neck concentrated on the region above lesser trochanter.

  结果在各种载荷下，股骨颈和股骨干各有一个应力集中部位。

• the maximum stress of cfrp on which reinforcement compound solutions is 2-4 times bigger than that of direct pasting and the high-strength effect of cfrp is used very well.

  试验中复合加固方案的cfrp布上的最大应力值比直接粘贴cfrp布的大2~4倍，很好地发挥了cfrp布的高强作用；

• test results show that both the decreasing speed of maximum stress and the increasing extent of maximum strain of concrete prisms increase as the heating temperature rises.

  试验结果表明，棱柱体的峰值应力下降速度和峰值应变增长幅度均随温度的升高而变大；

• it researches the stress condition, stress distribution, location of maximum stress and stress control criteria of rcc gravity-arch dam under different load combinations.

  研究碾压混凝土重力拱坝在不同的荷载组合工况下的应力分布状态和分布特征以及最大应力出现的位置和应力控制的标準。

• the results of fea method for cold-bending elbow predicted that the point of maximum stress is transferred from intrados to extrados with the increase of the wall thinning.

  并应用有限元方法分析了冷弯弯头的应力状况，得出其最大应力发生点随着外拱处壁厚减薄量的增大而向外拱处转移。

• using these measures and the adina finite element analysis can attain that, compared with the original structure, the maximum stress is loss than 15% of that of the original structure.

  通过这些措施及应用adina有限元分析得到轴承的最大接触应力降低至不足原结构的15%。

• the results showed that the optimal platen's mass was less than that of the original platen. also, its maximum stress and deformation was lower, and fatigue life was longer.

  结果表明，优化后的模型质量更小，且最大应力更小、变形更小以及有更好的耐疲劳性能。

• the alternation of the maximum stress region between the internal and external tube wall could led to local fatigue.

  应力最大区域交替出现在传热管的内外管壁上，易导致传热管局部疲劳失效；

• by the optimal design to the structural measurements of hot extrusion dies, the maximum stress in the body of improved dies is decreased by 32.2%, the lifespan is therefore prolonged.

  通过对模具结构尺寸的优化设计，改进后的模具体内最大应力下降32.2 % ，从而延长了模具的使用寿命。

• the maximum stress of pbga121 soldered joints increases when chip size increases, while the maximum stress of pbga81 soldered joints decreases first and then increases.

  芯片尺寸改变时，pb-ga121焊点的最大应力值随芯片尺寸的增大而增大，但pbga81的最大应力值随芯片尺寸增大先减小后增大。

• in the condition that mesh is divided into 9 lays , the maximum stress concentration factor is up to 1.57, in the place where practical burst was occurred.

  网格的细分凸显出了模型的结构上的边界效应，在网格划分为9层的情况下，最大的应力集中系数达到1.57。

• the inner maximum resistance force and the maximum stress of the specimen decreases as the deformation temperature increasing.

  在形变速率相同的条件下，随变形温度的升高，试样内部最大形变抗力及最大应力呈下降趋势。

• the result shows that load, seal gap and seal height have influence on the maximum stress while friction coefficient has little influence on it.

  分析表明，载荷、密封间隙、橡胶密封筒高度对应力最大值有影响，而摩擦系数影响很小。

• perforating in the maximum stress direction has been demonstrated to reduce sand production significantly. the challenge of orienting a perforating gun in vertical wells is well known in the industry.

  如果没有使用垂直应力导向射孔方案，油井的产量将会远远低于现有水平，且在生产过程中也极有可能出现出砂的情况。

• research conclusions:both irrational components outline and reinforcement design lead to increase in tension of(structural) component and maximum stress seat just as the crack site of real component.

  研究结论：不合理的构件轮廓与钢筋设计，将导致构件拉应力增大，而且最大值部位恰好是现场构件开裂部位。

• by numerical analyzing, both the maximum stress position generated by contacting, and the stress distributing curve of inner-outer races and contacting body were presented.

  通过数值分析，给出了内外圈和接触体的应力分布曲线以及接触产生的最大应力位置。

• the results showed that the maximum stress was located in the ground circle of the radome.

  结果表明受风载荷的雷达罩的最大应力发生在截球底座的边界上。

• choosing an appropriate bias spring can control the maximum stress and the minimum strain of the tini sample. this characteristic is effective to prevent the coupling system from overloading.

  通过配置偏置弹簧的刚度系数，可以控制样品输出的最大应力和最小应变，有效防止耦合系统过载。

• the probability distribution of the maximum stress in the component which depends on the ice thickness and ice compression strength is also given.

  同时还给出了取决于冰厚及海冰强度的构件上最大应力的概率分布；

• results compared with m model, d model provided much larger maximum stress in abutments and periodontal membrane.

  结果在基牙及其牙周膜，d模型基牙牙冠、牙根及牙周膜的最大应力均显着大于m模型；

• in designing the pressure container tube plate ansys software is used to analyze the stress of pressure container tube plate in this paper, and the maximum stress and displaced shape are showed.

  在压力容器管板的设计过程中，利用ansys软件对压力容器管板的应力进行分析，计算出压力容器管板的最大应力和应变，从而为压力容器结构的优化设计提供了充分的理论依据。

• with the increase of the grain size of h68 brass, the critical plastic strain for the onset of serrations increases while the maximum stress amplitude of serrations decreases.

  对于h68黄铜，随着晶粒尺寸的增大，出现锯齿屈服的临界应变量增大，锯齿波的最大应力振幅减小。