片语

test specimens[材][机] 试样

fuse arming test experiment piece条形保险丝

test-piece intensity试件强度

test-piece thickness试件厚度

sample bar试样

wedge test-piece三角试块

sheathing test-piece护套试样

Refractory test-piece preparation耐火试样制备

test-piece supports试样支座

fluidity test bar piece流动性直棒形试片

英汉例句

• the major technical specifications, construction and working principal of the test piece shear in the heavy plate mill of baosteel have been discussed in this paper.

  介绍宝钢宽厚板试样剪的主要技术参数、构成及工作原理；

• the casting concrete test piece is used to carry out blasting experiment under laboratory conditions, and then calculations are conducted using fore-mentioned approaches.

  在实验室条件下采用浇注的混凝土试件代替巖石进行爆破实验，然后应用提出的方法进行了分维数计算。

• the nitriding process comprises the following steps: cleaning the test piece again with the gasoline or acetone, or blowing sands on the test piece with low wind pressure fine sands;

  氮化处理工艺是将试件再次用汽油或丙酮清洗干凈，或用低风压细沙进行吹沙；

• this paper believes that the calculating formula of moment of inertia for bow-shaped test piece in gb/t 13096. 2-91 is wrong because of printing error.

  本文认为gb/t13096.2-91中计算弓形试样截面惯性矩的公式有误，同时指出在某些手册中有关计算公式也有误。

• the experimentation indicates that it is effective to measure the direct tensile strength and other character of concrete by change the size of the test piece and the way of loading.

  通过改变试件尺寸及加载方式，还可进一步探讨采用本试验方法测量混凝土的直接抗拉强度，研究混凝土的其它性能。

• the pin test piece was made of carbon, which came from a in-using pantograph strip. the disc was made of pure copper.

  销试件的材料为纯碳，取自铁路在用的受电弓滑板。

• the utility model relates to a liquid test piece for measuring liquid, which comprises a base plate, an interlayer, and a top head piece.

  本实用新型一种液体检测试片，用于液体量测，其包含一基板、一中间层、一上盖片。

• the test adopts test piece as the same at oil field. the article analyzes the corrosion rate and the corrosion form of p110 casing steel in corrosion fluid in two temp situations.

  试验采用与现场相同的腐蚀试件，具体分析了两种温度状态下p110套管钢在饱和盐水中的腐蚀速度和腐蚀形态。

• as a result, the effects of geometric size of test piece on j-r curve un-der different degree of constraint are argued.

  从而论证了不同约束条件下，试样的几何尺寸因素对其j阻力曲线变化趋势的影响规律。

• the testing on air flow dis-charge coefficient was done on a rectangular test piece in a simulatedcombustion chamber flow condition.

  试验是在矩形试验件上进行的，模拟了燃烧室流动状态。

• this test piece shall be welded using the identical welding parameters as the original test and only weld metal impact test specimens shall be tested.

  此试件应使用与原始试验相同的焊接参数进行焊接，并且仅对焊接金属沖击试样进行试验。

• if the test piece fails to comply with any of the requirements for visual examination or ndt specified in 7.5, one further test piece shall be welded and subjected to the same examination.

  如果试件不符合7.5规定的外观检查或非破坏性检查的要求，应再取一个试件进行焊接，并进行同样检查。

• after reaching the temperature of the furnace, maintain the test piece at that temperature for not less than 10 min.

  达到熔炉的温度后，将测试条保持放在熔炉里至少10分钟。

• structure of the mount model is modified, and stiffness measurement and fatigue durability test were made to the test piece before and after the modification.

  对悬置模型进行结构改进，并对改进前、后的试件进行了刚度测量试验和疲劳寿命试验。

• a field investigation of corrosion status of buried pipeline and measurement of the soil parameters were conducted, accompanied with corrosion test piece laying and field sampling.

  进行了现场腐蚀状况调研，对现场埋地管道的土壤腐蚀情况就地测量了相关参数，并进行了腐蚀试片埋设和现场取样工作。

• according to the standard's requirements, test piece for qualification of welding procedure and for product welding should be carried out various bending test.

  焊接工艺评定试板和产品焊接试板，按标準要求都要进行弯曲试验。

• using traditional interferometric method, as the germanium material is too soft to process, the surface form of the test piece may not meet the requirement for the measurement.

  运用传统的干涉法检验光学材料的折射率均匀性时，由于锗晶体太软，表面不易加工，其表面面形难以满足测试要求。

• it is permissible to change the specific make of filler material to another with the same compulsory part of the designation when an additional test piece is welded.

  当焊接附加试件时，允许将专用类型的焊料改为另一种具有相同规定部分的焊料。

• introduce a method of analyzing ferro-alloy test piece by fluorescent x-ray.

  介绍了x射线荧光分析铁合金试样的制备方法。

• according to different usages, the test station can be divided into voltage test station, current test station, protection effect test piece test station.

  根据作用不同有电位测试桩、电流测试桩、保护效果测试片测试桩。