片语

designed tooth side surface设计刀齿侧面

hardened tooth-surface硬齿面齿轮

reference tooth side surface基準刀齿侧面

tooth face[机] 齿面；齿尖面

tooth surface contact stress齿面接触应力

practical tooth side surface实际刀齿侧面

Tooth-surface quality齿面质量

Tooth h surface轮齿表面

worm tooth-surface蜗桿齿面

英汉例句

• gear final heat treatment using the parts deformation small tooth surface quenching;

  齿轮的最终热处理采用使零件变形较小的齿面高频淬火；

• a mathematical model of spiral bevel gear tooth surface was built by analyzing manufacture method and meshing theory.

  通过分析锥齿轮的加工方法和齿轮啮合理论，建立了螺旋锥齿轮齿面数学模型。

• to maintain healthy teeth and gums it is important that bristles contact both the tooth surface and the gumline.

  为了保持健康的牙齿和牙龈重要的是，无论是刷毛接触牙齿表面和牙龈线。

• the above research finds out the influence of grinder error and machining setting parameter error on tooth surface error of spiral bevel gear.

  上述研究查明了磨床误差及加工调整参数误差对螺旋锥齿轮齿面误差的影响机制。

• data of tooth surface before and after wear were both obtained through laser scan system. the images were then reconstructed by surfacer software.

  应用三维激光扫描仪采集牙模型的表面数据，在计算机中用surfacer逆向工程软件重建牙表面；

• this air scaler is intended to remove dental plaque, calculus and stain from tooth surface and tooth root by dental professionals only.

  本产品是由资质的口腔科医生在口腔科治疗过程中对患者的牙体表面所粘着的牙垢，牙结石，着色去除时所使用的设备。

• using the data of grids, the measurement process is completed automatically, the deviations of the real tooth surface from the theoretical one are obtained.

  由测量点数据，测量程序控制测针自动进行测量，从而测得真实齿面的结构参数。

• the error correction model of tooth surface was established by machine tool adjustment parameters and meshing principle.

  结合机床调整参数、齿轮啮合原理，建立了螺旋锥齿轮齿面误差修正模型。

• finally, it synthesizes the main factors which affect the fatigue crack of the tooth surface extension and form pitting under ehl conditions.

  最后，综合了在弹性流体动力润滑条件下影响齿面疲劳裂纹扩展形成点蚀的主要因素。

• screw compressor rotor tooth surface actually gaps between, and ability, can be pressed send impact liquid containing liquid gas, including dust, easy polymerization gas, etc.

  螺桿压缩机的转子齿面间实际上留有间隙，因而能耐液体沖击，可压送含液气体、含粉尘、易聚合气体等。

• the lubrication of tooth surface is the key to realize the transmission of steel worm-gear.

  结果表明：齿面润滑是实现钢蜗轮传动的关键技术之一，且齿面润滑对钢蜗轮传动性能影响很大。

• conclusion : it is indispensable to examine tooth surface before orthodontic bonding , and for the teeth which present enamel crack the etching duration should be controlled exactly.

  结论：常规的酸蚀处理可能对存在釉质裂的患牙造成过度损伤，在临床正畸粘接前，应对牙面进行仔细检查，对存在釉质裂的牙齿，应严格控制酸蚀时间。

• the deviation between actual measured pitch value between any adjacent tooth surface and theoretical circular pitch.

  实测任何相邻的两个齿间的径节值与理论径节值的偏差。

• the distribution feature and the fluctuation tendency of the temperature in the vicinity of the worm wheel tooth surface were investigated and analyzed.

  分析了邻近蜗轮齿面的温度分布特征及温度变化的趋势。

• abstr: the helical groove zc1 worm tooth surface grinding process is key to achieving their finishing, and grinding the process also has a number of factors determine the quality of the grinding worm.

  文章摘要：螺旋凹齿面zc1蜗桿的磨削加工是实现其精加工的关键工艺，在磨削过程中有多种因素决定着蜗桿磨削加工的质量。

• the top grade silica abrasive, gently remove tooth surface dirt and tooth enamel surface doesn't hurt, often use, strong teeth, healthy mouth.

  采用高档二氧化硅磨料，轻柔去除牙表面污垢的同时不伤害牙表面珐瑯质，经常使用，强健牙齿，健康口腔。

• thejmeth-od is objective measure for tooth surface phosphorescence and reflex light to realized.

  这种方法，是通过对牙齿表面磷光或反射光的客观测量来实现的。

• the content of this research is as follows:direct modeling for tooth surface of ti worm in ansys is difficult for the equations of contact lines being a kind of transcendental function.

  主要研究内容如下：由于ti蜗桿齿面上的接触线方程是一种超越函数，直接在有限元分析软件ansys中建模比较困难。

• by using the tooth edge contact analysis and finite element method, the maximal stretched stress, maximal compressed stress and tooth surface contact stress of the hypoid gear are analyzed.

  利用有限元和边缘接触分析方法，讨论了上述方法设计出的齿轮副齿根最大拉伸应力、齿根最大压缩应力以及齿面接触应力的变化；

• the micro angle induced by the tooth surface elastic deformation causes the change of meshing points. quasi-hertzian analysis is defined as the process of tooth meshing analysis.

  将齿轮因齿面变形而产生微小转角，继而进行齿面啮合分析的过程定义为拟赫兹接触分析。

• study on the error correction technique of tooth surface using truncated singular value decomposition(tsvd).

  基于截断奇异值分解法的齿面误差修正技术的研究。