英汉例句

• the annealing temperature is the crucial one.

  其中退火温度是决定性的因素。

• the optimum annealing temperature of al alloy anode was 550 ℃.

  铝合金阳极的退火最佳温度为550℃。

• recrystallization diagram of this alloy has been determined. the effect of degree of cold work and annealing temperature on deep drawing properties of the alloy are studied.

  测定了该合金的再结晶全图、冷加工变形度和再结晶退火温度对该合金深沖性能的影响；

• tbe present paper is devoted to describe the effect of the implanted energy, dose, and annealing temperature and time on electrical characteristics of circuit components.

  文中着重介绍了注入离子能量、剂量、退火温度及时间对电路元件电学性能的影响。

• so to shorten annealing temperature and time is a vital issue.

  因此，降低退火温度，缩短退火时间是一个急待解决的问题。

• the scanning images of electron microscopy show that high annealing temperature or high laser energy can induce the nanocrystalline si film with mazes.

  扫描电子显微镜的结果表明，高的退火温度或高的激光能量均会导致迷津结构的形成。

• the influences of different annealing temperature on the structure and hardness was compared and investigated. the proper annealing temperature for the bainite nodular iron roller ring was proposed.

  对比研究了不同退火温度对贝氏体球铁辊环组织和硬度的影响，提出了贝氏体球铁辊环合适的退火温度。

• the optimal middle annealing temperature increases with the increase of the carbon content.

  合金的最佳中间退火温度随碳含量的增加而升高。

• with annealing temperature increasing from 300 ℃ to 600 ℃, the yield strength and tensile strength decrease and the elongation increases.

  退火温度从300℃升高到600℃时，合金屈服强度和抗拉强度降低，伸长率升高。

• experimental results indicate that the micro-hardness of electroformed nickel shaped charge liner decreases obviously as the annealing temperature rising and the grains show equiaxed in shape.

  试验结果表明，随着退火温度的升高电铸镍药型罩的显微硬度明显降低，内部晶粒呈现等轴晶形态。

• as a matter of fact, the annealing temperature and time influence the transition of the semicond-uctive as-grown fiber to superconductor which is a peritectoid reaction.

  半导体性质的定向生长棒向超导体转变的退火过程实际上是亚稳相的包析反应，退火温度和时间都对反应有影响。

• the results show that the thermal diffusivity decrease with annealing temperature elevating.

  结果表明：纳米氧化铝的热扩散率随退火温度的升高而减小。

• the results indicate that the blue shift of band gap depends on the annealing temperature and annealing time. choosing reasonable annealing condition can control the magnitude of blue shift.

  实验结果表明，带隙蓝移同退火时间和退火温度有关，合理选用退火条件可以控制带隙的蓝移量。

• for the deposited films, the electrical conductivity increased with the annealing temperature and meanwhile the mobility and carrier concentration also increased.

  蒸发膜在不同气氛下退火，电导都随温度升高而增大，同时迁移率和载流于浓度都有增加。

• the effect of finishing rolling ratio, softening annealing temperature and grain size on the 4004/ 3003/4004 aluminum alloy brazing foil is studied in this paper.

  研究了4004/3003/4004钎焊用铝合金箔材的成品轧制率、软化退火温度以及晶粒尺寸时其抗下垂性能的影响。

• the results of magnetic measurement showed that the optimum annealing temperature for high permeability is about 540℃.

  磁性测量结果表明，获得高磁导率的最佳退火温度约540℃左右；

• at the same time, the concentration of template dna, annealing temperature and cycle times of pcr procedure were selected too.

  同时又对dna模板浓度，pcr扩增程序中的退火温度及循环次数进行了筛选。

• the optimum middle annealing temperature depends on the chemical composition of the alloys.

  而最佳中间退火温度受合金成分的影响。

• the optical absorption edges red-shift along with the increase of annealing temperature under nitrogen and blue-shift under air were observed, which can be attributed to the quantum size effect.

  在氮气和空气中退火时，随退火温度升高前者表现为红移而后者表现为蓝移，这归属于量子尺寸效应。