英语释义

1. to combine or impregnate (a metal) with carbon

片语

Carburization Kerosine渗炭用煤油

carburization zone[材]

Carburization behavior碳化行为

accelerate carburization快速渗碳

self carburization自增碳

acieration表面钢化；[化学] 碳化；[材] 渗碳

carburization treatment渗碳处理

gaseous carburization气体渗碳

case-carbonizing渗碳；表面渗碳

gas carburization气体渗碳

英汉例句

• on the basis of simulation result, the influence of carburization temperature on the dual phase concentration field was discussed.

  在模拟结果的基础上，进一步讨论了渗碳温度对低温两相区渗碳浓度场的影响。

• new technology that altering temperature and low pressure carburization is put forward in allusion to low quality and high cost of gears.

  针对耐磨构件，尤其是齿轮等机械构件质量低和生产成本高的现状，提出变温低压渗碳新工艺。

• the study on carburization of molten iron of bf at dropping process;

  渗碳工艺在机械行业中扮演着重要角色。

• in this paper, the carburization behavior and its effects on the mechanical properties of several commercial alloy steels for pyrolysis furnace tubes were studied.

  研究了乙烯裂解炉管常用材料的渗碳行为及对其力学性能的影响。

• the basic principle of surface-treating technique for protecting metals from carburization by forming a dense and continuous oxide layer with high stability was introduced.

  阐明了采用表面处理防止金属材料产生渗碳腐蚀的基本思路是在欲防护工件表面形成具有高稳定性的致密、连续的氧化物。

• distortion of automobile synchronizer gear sleeves will take place during the course of carburization and quenching.

  汽车同步器齿套在渗碳淬火后，发生变形。

• the result of the experiments points out that the elbow bursting is caused by thinning. the high temperature oxidation, carburization and heat fatigue also have some advance effect on elbow thinning.

  结果表明，炉管弯头的破裂是管壁减薄引起的，并且高温氧化、渗碳、温差应力及热疲劳等对弯头减薄破坏也起着很大的加速作用。

• for the iron and steel industry in the quenching of cutting tools for the steel of carburization .

  钢铁工业中用于切削工具的淬火处理，作钢材的渗碳剂。

• the result shows that carburization was the major factors inducing the failure of the furnace tubes.

  结果表明，渗碳是引起炉管失效的主要因素。

• at the same time, the titanium cermet femoral head was also produced by this technique. thermodynamics and kinetics of the carburization were analyzed to understand the sequential diffusion mechanism.

  本文通过材料热力学和动力学分析研究钛金属陶瓷的制备工艺，充分理解钛合金渗碳的分级扩散机理。

• aging and carburization during the service produced precipitation of carbides, the amount, size and forms of which depended on the service time and working temperature.

  炉管服役过程的时效与渗碳导致大量碳化物的析出，其数量、大小与形态取决于服役温度和时间。

• the topic of this graduation project is:two grades computer carburization process distributed control system.

  本次毕业设计的题目为：两级计算机实现的渗碳过程集散控制系统。

• this model is used to achieve the calculation and actual time control of deep carburization with high concentration.

  应用该模型实现了高浓度深层渗碳的计算机实时控制。

• carburization and its harm to ethylene cracking tubes is introduced.

  介绍了乙烯裂解炉管的渗碳过程及其危害性。

• possible surface carburization may be detected optically in spheroidized materials by observation of surface pearlite or an increased number of carbide spheroids.

  通过观察球光体表面或碳化物的增加的数目在球化处理材料方面，在视力上发现可能的表面渗碳。

• the high carbon concentration carburization for cr-mo steel was introduced.

  介绍了铬钼钢的高浓度渗碳试验。

• carburization is the heat treatment process which carbon atoms permeate into the steel work form its surface.

  而工件的渗碳处理是使碳原子渗入钢制工件表层的化学热处理工艺。

• experimental study of plasma carburization technology and analysis of wear test of carburizing layers are done aimed at alloy bar grate material surface.

  针对合金篦条材料表面进行等离子渗碳技术的试验研究和渗层的耐磨性能实验分析。

• a cylindrical carburization sample was placed in the coils. the case was separated into a lot of small piece and finite element method was used to solve the electromagnetic field.

  对于无明显分界面而具有连续硬化层的渗碳材料，通过把渗碳层离散化为足够多的小区域，模拟其电磁特性在空间连续分布的情形，然后采用有限元法进行求解。

• the mathematical model of gas carburization is mathematical description of all kinds of physical and chemical phenomena in the process of carburization .

  气体渗碳数学模型是渗碳过程中各种物理、化学现象的数学描述。

• carburization of molten iron in the dropping zone of bf has been studied. the results show that there are many factors affecting the carburization of molten iron.

  对熔融铁水滴落过程的渗碳规律进行了研究，研究结果表明：影响高炉铁水渗碳量的因素是多方面的。

• plane warping deformation and interior hole oval deformation occur easily for spread bevel gear at carburization and hardening.

  螺旋伞齿轮在渗碳淬火时极易发生平面翘曲变形和内孔椭圆化变形。

• fatigue properties of three case hardening steels for heavy duty gears after carburization were investigated by means of rotating bending fatigue tests.

  利用旋转弯曲疲劳试验方法研究了三种重载齿轮钢渗碳后的疲劳性能。