片语

contact initial pressure[电]

contact area pressure接触面压力

contact line pressure接触线载荷

nominal contact ground pressure名义接地压力

first contact miscibility pressure一次接触混相压力

contact-pressure resin接触成型树脂

contact area pressure ratio接地比压

contact area pressure distribution接地压力分布

Contact Making Pressure Gauge电接点压力表

英汉例句

• the article bases on the result of elastic-optic experiment and uses the energy method, roll theory and thick tube theory to calculate the contact pressure in ringent and close section.

  根据全息光弹实验结果得出的轧辊接触压力的分布规律，进而利用能量方法、轧压理论及厚壁筒理论对开口孔型、闭口孔型的轧辊接触压力进行计算。

• the contact pressure of the side cleaning brush during cleaning can be controlled by the tested reliable equilibrium technology.

  侧面清洗刷清洗过程中的接触压力经过测试的可靠的均衡技术来控制。

• according to the deformation coordination and force balance condition of shell, the mathematical model to solve the contact pressure between shell and tyre was established.

  根据滚圈处筒体的变形及力平衡条件，建立了计算滚圈与筒体间接触压力分布的数学模型。

• the technique of directly measuring the contact pressure was employed and the method compared with the indirect method.

  该方法是采取直接测量接触压力分布技术，并与间接测试方法进行了比较。

• the maximum contact pressure is decreased with the increase of the r value, and the change of r value has more remarkable influence on the maximum contact pressure of the small dimension oil seal.

  最大接触压力随r值的增大而逐渐减小，且r值的改变对于小尺寸油封最大接触压力的影响较大；

• particle penetrating direction has influences on the magnitude of surface deformation, contact pressure and stress, and the distribution forms of contact pressure and stress.

  磨粒侵入方向不仅影响材料表面变形、表面接触压力和表层应力的大小，而且会引起压力和应力分布形状的改变。

• by the self-balancing computation of the prestressed tendon of arch foot, a formula of contact pressure was acquired.

  通过对拱脚预应力钢索进行自平衡的计算，得到了接触压力荷载的公式。

• stranded conductors shall not be consolidated by soldering where they are subjected to contact pressure, unless the contact pressure is provided by spring terminals.

  多股导线在其承受接触压力之处，不应使用钎焊将其焊在一起，除非由弹簧接线端子提供接触压力。

• the rings (for materials see table 6.1) are heat-treated in different ways according to the strain on the gear rings and the contact pressure of the area carrying the highest load.

  戒指（材料见表6.1）的热以不同的方式处理根据齿轮上的戒指，在载有最高负荷区接触压力的压力。

• influences of the variation of initial angle of frictional facing on the contact pressure and the efficiency factors were analyzed.

  分析了摩擦衬片初始角变化对接触压力及效能因数的影响。

• the method of force analysis of the reducer is proposed on the basis of a supposition of the distribution of contact pressure between the push rod roller and the gear rack.

  介绍了这种减速器的结构和工作原理，并根据变形分析对齿条与推桿滚子间的接触压力分布做了假设。

• according to the deflection coordination condition of shell, the distribution rule of contact angle and the contact pressure between shell and tyre are obtained.

  根据滚圈处筒体的变形及平衡条件，得出了筒体—滚圈的接触角及筒体—滚圈的接触压力分布规律。

• taking an arch foot as an example, a practical met hod was proposed to simulate the contact pressure of the prestressed tendon according to the experiment.

  以桥梁拱脚为例，依据实验结果提出了一种模拟预应力钢索与索道壁之间接触压力等代荷载的实用的方法。

• the sweeper installation, adjustment and the contact pressure should comply with the requirements of the specification of factory.

  清扫器的安装、调整及接触压力等应符合厂家说明书的要求。

• a simple and practical method was proposed to simulate the contact region and the contact pressure between the prestressed tendon and the wall of ropeway.

  根据试验观察，提出了一种模拟预应力钢索与索道孔壁接触区域和接触压力的简单、实用的方法。

• conclusions:there is a normal contact area between the inner surface of lateral femoral tendon and lateral femur condylar to reduce the contact pressure of the lateral surface of patella.

  结论：①在正常情况下股外侧肌腱内面与股骨外侧髁存在着接触，这可能是缓解髌骨外侧关节软骨面压力的正常接触；

• conductors of supply cords shall not be consolidated by soldering where they are subjected to contact pressure, unless the contact pressure is provided by spring terminals.

  电源线的导线在其承受接触压力之处，不应使用钎焊将其合股加固，接触压力由弹簧接线端子提供。

• pressure the general assembly to premature seal failure, and the contact pressure is too small will cause leakage.

  压力过大会促使密封过早失效，而接触压力过小则会引起泄漏。

• the main measuring method of tire contact pressure is using stress sensor.

  轮胎接地压力测试方法主要是压力传感器法。

• the goal of this study was to determine the effects of posterior root tears of the medial meniscus and their repairs on tibiofemoral joint contact pressure and kinematics.

  本研究旨在确定内侧半月板后角撕裂的生物力学特性，以及修复后对胫股关节接触压力和动力学的影响。

• study selection: after the first trial to the data, the studies on contact and contact pressure were selected.

  资料选择：对资料进行初审，选取与股胫关节接触判断方法、接触压力分析相关的文献。

• the effect of axial dimension on the hysteresis and contact pressure of the finger seal mechanism is analyzed by the adoption of contact models with fem (finite element method).

  采用有限元接触模型分析了指尖密封片轴向尺度对指尖密封的迟滞特性及接触压力的影响。

• the result shows that with the increase of sealing medium pressure, the contact pressure on the bottom of o-sealing ring gradually increases under the different included angles.

  结果表明：随着密封介质压力的增加，各夹角时o形密封圈底部的接触压力都逐渐增大；

• the roll separating force, rolling torque and contact pressure along the surface of the rolls are also evaluated by means of the finite element method.

  轧制分离力、轧制力矩以及沿轧辊表面的接触压力也通过有限元法进行评估。

• the calculated results indicate that the axial distributions of the maximum contact pressure have an 「s」 shape.

  结果表明，最大压应力轴向分布呈s形，原辊形会引起接触应力集中。