In addition, lengthening the cooling time or lowering the cooling rate can reduce the residual stresses.

另外，延长喂料冷却时间或降低喂料的冷却速率有助于减小残余应力。

The kelvin cooling time for the earth is then about30000years.

在开尔文的冷却时间，地球是那么大约3。0万年。

The theoretical prediction values of the surface temperature of heavy rail, the straightening temperature and corresponding cooling time are in reasonable agreement with experimental results.

重轨表面温度、矫前温度及相对应的冷却时间计算值与实测结果基本相符。

This high pressure was the cause of higher melting temperature and increased cooling time for plastic part.

这种高压力较高的熔融温度，增加冷却造成塑料的一部分时间。

The significant factors are cooling time and freezing temperature.

其中冷冻时间，冷冻温度的影响最为显着。

Short heating or cooling time and stable temperature.

加温及冷却时间快速，温度稳定。

This paper intends to study the influence of rapid cooling time after rolling on the microstructure and mechanical properties of low-carbon steel.

本文研究了轧后快冷时间对控轧低碳钢板组织和力学性能的影响。

The quality of the hollow blow molding plastic products is affected by various process factors, such as melt temperature, inflation pressure, stretching rate, cooling time and polymer property, etc.

中空制品的吹型成型质量受各种工艺因素的影响，包括熔融温度、吹胀压力、拉仲速率、冷却时间、聚合物材料柱能等。

The packing time is about 80% of the cooling time which itself is often less than that which is set.

保压时间大约是冷却时间的80%，冷却时间常常小于其设定值。

To establish production cycle also effects, such as the filling time, cooling time and spraying time are based not stable variables.

对生产周期也建立影响，如填充时间、冷却时间及喷涂时间都建立不稳定的变数。

The algorithm of calculating the equivalent distance of the Jominy sample was deduced by making use of the same cooling time in the Hardenability Sensitive Temperature Range as the cooling criterion.

以淬透性敏感区间内的冷却时间相同为冷速判据，得出了直接计算等效端淬距离的算法；

Jig for special PET, compelling cooling, shorten the cooling time in the mold.

特殊瓶胚专用治具不伤瓶胚，强制风冷，缩短模内冷却时间。

「You get higher output due to reducing the cooling time needed, and there's also less warping of the paper due to lack of heat, which leads to higher paper strength,」 van Leeuwen added.

「降低了生产所需要的冷却时间会带来更高的产量，而且由于没有高温影响，纸板变形现象也会更少，」范?鲁凡补充说。

When the laser scanning speed increases, the laser radiation and cooling time get shorter, so the growing direction of microstructures is changed sharply.

提高激光扫描速率，造成激光辐射和冷却时间变短，合金微观组织生长方向变化显着；

Using this model, evolution profile of electron temperature with heating time in ionospheric D/E region, heating and cooling time scale, are calculated in this paper.

使用这个模型，演化与D /E区电离层的加热时间，加热和冷却时间尺度的电子温度的档案，在本文的计算。

Several methods to determine the cooling time of injection molded slabs of crystalline plastics are discussed based on the theory of heat transfer.

从传热学基本原理出发，推导出结晶性平板状注塑制品冷却时间的几种计算方法。