英语释义

• a rotating shaft driven by (or driving) a crank

片语

crankshaft compartment曲轴区

tca crankshafttca曲轴

crankshaft governor曲轴调正器

v crankshaftv240曲轴

crankshaft installation曲轴安装

engine crankshaft发动机曲轴；动力机曲柄轴

crankshaft flywheel曲轴飞轮

crankshaft surface曲轴表面

Crankshaft housing曲轴箱

crankshaft lathe[机] 曲轴车床

英汉例句

• in lanchester’s design, two balance shafts rotated in opposite directions at twice the crankshaft speed to cancel out the niggling secondary vibrations.

  lanchester的设计中，两个平衡轴以两倍于机轴转速，反向地转动，抵消了无用的次生振动。

• reciprocating compressors is using the piston, the crank, link mechanism or the piston, the crank, sliding tube institutions, rotary compressor rotor is the use of crankshaft institutions.

  往复式压缩机使用的是活塞、曲柄、连桿机构或活塞、曲柄、滑管机构，旋转式压缩机使用的是转轴曲轴机构。

• crankshaft is an important part of truck engine parts, and it is also a fast moving parts.

  曲轴是一个重要的组成部分卡车发动机部件，而这也是一个快速移动的零件。

• this variety of options provides flexibility for achieving solutions for a wide range of applications, including automotive transmission and crankshaft speed sensing.

  选件的多样性可以更灵活地为各种应用（包括汽车变速器和机轴速度感测）提供解决方案。

• the flywheel mounts to the engine's crankshaft and transmits engine torque to the clutch assembly .

  飞轮安装在发动机曲轴上，它将发动机的扭矩传递给离合器总成。

• remove front crankshaft belt pulley.

  拆卸前曲轴皮带轮。

• because the crankshaft is built up inside the case, the bases of the rods do not need to be split and bolted back together.

  由于曲轴建立了内部的情况下，该基地的燃料棒不需要分割和螺栓重新走到一起。

• for the secondary forces to be in balance, the rods connecting the pistons to the crankshaft would have to be of infinite length.

  为了平衡不受控制的力，连接活塞和机轴的桿不得不变得无限加长。

• the water pump is a simple centrifugal pump driven by a belt connected to the crankshaft of the engine. the pump circulates fluid whenever the engine is running.

  水泵就是一个简单的离心泵，用皮带连接发动机上的曲轴。发动机无论何时运转水泵都能循环起来。

• the nationalization of engine crankshaft blank for jetta bora and golf car was realized.

  实现了捷达、来和高尔夫轿车发动机曲轴毛坯的国产化。

• from the point of view of the design, the counterweight design for the balance is one of the tasks of the crankshaft design.

  从设计的角度来说，曲柄平衡的配重质量设计是曲轴设计任务的一部分；

• the combustion process pushes the piston down the cylinder with great force turning the crankshaft to provide the power to propel the vehicle.

  其燃烧过程产生的巨大力量的推动着活塞向下运行，带动曲轴而产生推动汽车的动力。

• the second photo shows the crankshaft center bearing holder installed in the block.

  第二图为曲轴中心轴承持有人安装在该区块。

• the engine could also use some crankshaft counterbalance to make it run smoother.

  该引擎也可以使用一些曲轴平衡，使其运行顺畅。

• camshaft from the crankshaft through the timing belt or gear or chain drive.

  凸轮轴由曲轴通过齿形带或齿轮或链条驱动。

• if chain is not satisfactory, remove camshaft sprocket attaching bolt and remove timing chain with crankshaft and camshaft sprockets.

  若正时链不令人满意，则拆下凸轮轴链轮固定螺栓，并拆下曲轴和凸轮轴链轮的正时链。

• in conclusion, the connecting rod and crankshaft mechanism of the engine is composed of various units, and each of these units has its own functions in producing power for vehicles.

  总得来说，发动机中连桿和曲轴这一机械装置由多种部件组合而成，为了能够让机动车辆产生动力这些部件中每一个都有着其特定的作用。

• install new front crankshaft oil seal.

  安装新的前曲轴油封。

• in that way, the forces acting on the crankshaft are balanced and vibration is reduced.

  以这种方式，在曲轴上的力将会达到平衡而且震动也会减少。

• the stress and deformation of crankshaft are calculated by finite element method with six load boundary conditions and three displacement boundary conditions.

  分别采用六种载荷边界条件和三种位移边界条件对曲轴应力和变形进行了有限元分析；