片语

deep drawing force拉深力

pulling force[力] 拉力；牵引力；引力；牵力

drawing force transducer拉力传感器

backward drawing force反拉力

tension使紧张；使拉紧

ultimate drawing force极限拉拔力

drawing shell force抽壳力

drawing internal force diagram绘内力图

drawing force tester拉拔力测试机

英汉例句

• based on the assumption, the computer was used to calculate the minimum deformation energy, and the speed distribution in the deformed area and the drawing force were gotten.

  在此基础上利用流函数建立了变形区速度场，并利用计算机对变形能进行求极小值，得到了变形区的速度分布及拉拔力。

• the thinning drawing force is calculated through deforming work method and slip-line method irrespectively, and the results are compared in this paper.

  本文用变形功法和滑移线法分别求解变薄拉深力，并将两种方法的计算结果进行了比较。

• through a series of drawing experiments of brass wires, the effects of ultrasonic vibration on drawing force and surface quality of the wires were discussed.

  系统由超声波驱动器、换能器、变幅桿、拉丝模、拉伸机等组成，通过对黄铜丝的拉拔实验，考察了超声振动对拉拔力和丝的表面质量的影响。

• the formula of drawing force for cold-drawn inner fin tube is derived with slab method in this paper.

  采用工程法推导了冷拔内直筋管拔制力的计算公式。

• a formula of drawing force in empty sinking of tubes with equal wall thickness is derived depending on a continuous velocity field in cylindrical coordinate system.

  利用圆柱坐标系的连续速度场推导出圆管等壁空拉拔制力的计算式。

• in this paper, the method of measuring total drawing force and limit drawing ratio is applied to test the performance of the drawing lubricant.

  本文介绍利用测试总拉深力和极限拉深比的实验方法，研究拉深用润滑剂的粘度和凹模圆角半径对拉深成形工艺的影响。

• objectivein order to quantify the treatment of fractures with splint, we develop discal index drawing force transducer for measuring and controlling the sanction of fixation retainer of the splint.

  目的为实现夹板局部外固定治疗骨折的定量化，我们研制了盘状指针式拉力传感器以便实时监控夹板固定带约束力。

• an effective way for enhance of magnetic ring drawing force has been sought out.

  找到了提高磁环牵引力的有效方法；

• the drawing force decreases and the specific elongation increases when the frequency of pulse current exerting to wire adds in the scope of experiments.

  在实验范围内，施加的脉沖电流频率增加时，拉拔力降低，合金丝的延伸率增加。

• drawing force under free roller dies drawing is much smaller than that under fixed rolls drawing.

  辊模拉拔辊拉力明显小于固定辊模拉拔。

• technology analysis, strength calibration, calculation of drawing force and the design proposal improving for upgrading from 400t to 500t is introduced.

  介绍了40 0 t拉伸机扩能改造为5 0 0 t的技术分析、强度校核、拉伸力计算和改造方案设计。

• so the solution can be used to calculation of drawing force during draw-out by idle rolls.

  因而，该解析解可在工程上计算圆管辊拔拔制力时推广应用。

• the function of apt backward drawing force in wire drawing is analysed and. the problem of determining and controlling apt backward drawing force studied.

  分析了合理反拉力在拉丝过程中的作用，并对如何确定和控制合理反拉力的问题进行了探讨。

• it is shown that steel strength can be decreased, plasticity can be increased and drawing force can be reduced by electroplastic drawing.

  试验结果表明，电塑性加工技术，可有效地降低钢丝生产中的拉拔力，降低钢丝的强度，提高塑性。

• the invention provides a pipeline connector which avoids reducing the pipeline flow, increases the drawing force and effectively solves the pipeline leakage.

  本发明提供一种避免减少管路流量、增大拉拔力、有效解决管路泄漏的管道连接件。

• the said experiments show that with the roll-die drawing process the drawing force can be considerably reduced and surface quality of the shape steel tube improved.

  试验证明，辊拔工艺可显着降低拔制力，提高异型钢管表面质量。

• when the roller passes through the roving, a certain twist level can be untwisted, and thereby the drawing force is reduced.

  当粗纱须条 在辊轮经过时能退去一定的捻度，使牵伸力降低。

• the upper-bound solution proves that the theoretical value of drawing force is basically the same as that from experiments with relative errors permissible.

  实践证明，拔制力理论计算值与实测值相比，其相对误差在工程允许的误差范围之内。

• elementary reason affecting the drawing force and direct pressure force is given, the reasons of energy saving and cost reduction with the roller dies drawing is revealed.

  给出了影响拉拔力和正压力基本因素和辊模拉拔节能降耗的原因。

• the formulas of drawing force for spiral internal-ribbed pipe cold-drawing are derived with upperbound method.

  利用上界法推导了冷拔内螺旋凸筋管拔制力计算式。

• in a certain range. drawing force is reducing along with the increasing of drawing speed, which was reached by test.

  通过试验得出拉拔力在一定范围内是随着拉拔速度的提高而降低的。

• the law that drawing force changes with drawing speed is analyzed. it is raised that increasing wire drawing speed can improve labour productivity, save energy and reduce consumption.

  分析拉拔力随拉拔速度的变化规律，指出提高钢丝拉拔速度可提高劳动生产率和节能降耗。

• excite the interior drawing force of students' cooperating correcting.

  激发学生合作评改的内驱力；