片语

drilling water hole打水眼

drilling g hole鉆孔

drilling radial hole鉆径向孔

drilling precise hole鉆精孔

drilling new hole鉆新孔

bouche(Bouche)人名；(法)布什；(德)布赫

drilling conductor hole鉆导管井眼

Drilling Making hole正鉆

directional drilling hole定向鉆孔

drilling core hole鉆芯孔

英汉例句

• Through analyzing the characteristics of the part, according to drilling hole on the conical surface, designed the special clamping tool.

  通过对零件的工艺性分析，针对零件要在锥面上鉆孔的特点所设计的专用夹具。

• The critical pressure and conditions of drilling hole burst are determined through the physics experiment of drilling hole burst.

  通过鉆孔沖击物理试验，研究了鉆孔沖击的临界压力，以及鉆孔沖击的条件；

• The processing efficiency is low but the labor cost is high when the traditional method for drilling hole is used, also the processing precision is difficult to guarantee.

  采用传统鉆孔加工方法，加工效率很低，人工成本很高，且加工精度质量很难保证。

• The present applied calculation method is very complicated and low calculating accuracy, and this method can not determine the drilling hole position.

  目前实际中采用的计算方法很繁杂，计算精度低，而且不能给出最优的鉆孔位置。

• Remove stem assembly (A) and lock setting by drilling hole and inserting dowel pin (C).

  拆卸阀桿总成（A），并且通过鉆孔锁定设置和插入定位销（C）。

• The method of rotary drilling hole and protecting hole wall by static mud is an advanced technique to drill hole.

  静态泥浆护壁旋挖成孔工艺是一项先进的成孔工艺。

• In this paper, analytic geometry is drawn into drilling hole position calculation and have the aid of computer, the calculation is accurate.

  本文引入解析几何，借助计算机对鉆孔位置进行较精确计算。

• It is difficult to pull out the bolt with ordinary socket wrench that can not provide axial tension because of the bolt drilling hole deformation and the collapse of holes.

  煤矿井下可回收锚桿一般用于煤层巷道，由于锚桿鉆孔的变形和塌孔等原因，用普通套筒扳手拆卸锚桿时，因不能给锚桿提供轴向拉力，很难将锚桿拆卸拔出。

• Second, the bottom panel of the surface to avoid led drilling hole position is fixed by the screw to install wall on, installed according to the design of plate and fixed thread on each word.

  将面板底面避开LED位置鉆孔用螺丝固定再安装壁面上，按设计之板安装好，并将每个字的线头固定好。

• A section bar of a self tapping screw for saving drilling hole is provided with high-tightening force, which belongs to the design preparation technical field of the section bar.

  可免鉆孔上自攻螺丝并具有高紧固力的型材，属型材的设计制造技术领域。

• Product specification is a circular grinding mill, plane, grinding, drilling hole etc.

  产品规格有外圆砂轮、平面磨、磨片、开孔鉆头等。

• Oil gas diffusion can probably occur from the product pipeline due to some factors such as pipe corrosion, foreign power collision, oil stolen by drilling hole or water hammer.

  成品油管线在运营过程中会发生泄漏，主要原因为管线腐蚀、外力撞击、打孔盗油及水击等，泄漏后油品蒸发扩散形成的爆炸性区域具有很大的危险。

• The paper also presents measures for preventing drilling hole curve, drilling technique in broken zone and fissure zone and technique of sealing hole and pluging loophole.

  预防锚孔弯曲的措施；破碎带、裂缝带的鉆进技术及封孔固壁堵漏技术。

• It is said that under Pine Gap is the deepest drilling hole in Australia - about 5 miles (more than 8,000 meters).

  这是说，根据松峡是最深鉆孔在澳大利亚-约5英里(8000多米)。

• The image of drilling hole can be intuitively given by using ultrasonic detection.

  利用超声波对鉆成孔进行检测，可以直观地给出鉆孔的垂直度、孔径等参数。

• This paper introduces the appraisal principles and methods of engineering changes are caused by geologic changes in drilling hole pour pile.

  介绍了鉆孔桩地质变化引起的工程变更的估价原则和估价方法。

• It can improve gas suction effect, reduce drilling hole amount and save construction investment.

  采用优化后的方法可以提高瓦斯抽放效果，减少鉆孔数量从而节省施工投入。

• The first drilling hole of the Wenchuan earthquake fault science drilling project (WFSD-1) experienced up to more than 30 meters of the fault gouge drilling process.

  汶川地震断裂带科学鉆探项目一号孔(WFSD - 1)鉆遇了30多米的断层泥。

• Based on the comparing and analysis, it points out the reason of lower load capacity of dive drilling hole pile.

  在比较分析的基础上，指明导致潜水鉆成孔灌注桩承载力较低的原因。