片语

FEA Engineer有限元分析工程师

linguistic fea语言特征

fea results有限元结果

FEA load有限元载荷

FEA implementation有限元移植

fea software有限元分析软件

LUSAS FEA桥梁工程

FEAabbr. （美国）联邦能源署（Federal Energy Administration）

fea cathode场发射阵列阴极

英汉例句

• Abstract: in this article, we shall talk about the FEA of the static intension of crankshaft, and find out the dangerous case and area exactly with less cost.

  摘要：本文介绍用有限元方法对曲轴的静强度进行分析，用较小的耗费準确的确定了曲轴的危险工况及危险区域。

• Based on the heat conduction theory, the FEA theoretical formulas of temperature field and thermal stress are deduced in this paper.

  本论文从热传导理论出发，推导出温度场和温度应力的有限单元法理论公式。

• Then we use the FEA software to analyze the structure again, and the theory calculations and the practical results shows that our scheme on the modification is successful.

  因此，给出了整改方案，并对整改后的结构再次进行了有限元计算，理论计算和实践结果均表明此整改方案是成功的。

• The results of FEA method for cold-bending elbow predicted that the point of maximum stress is transferred from intrados to extrados with the increase of the wall thinning.

  并应用有限元方法分析了冷弯弯头的应力状况，得出其最大应力发生点随着外拱处壁厚减薄量的增大而向外拱处转移。

• The basis method of the FEA experiment platform for cleaning element in brush shape is elaborated.

  阐述了排刷式剥叶元件有限元分析试验平台设计的基本方法。

• Secondly, an FEA model is built, in which the plate offset effect is considered for the tank walls of variable thickness, and the effect of the seismic load is analyzed.

  在有限元计算模型处理时，对由不同厚度钢板焊接而成的罐壁进行了板壳元的厚度偏移处理，并详细讨论了地震载荷的计算和影响。

• The electrodes, insulator layer and FEA layer are fabricated by sputtering.

  通过溅射的办法制备了各层电极、绝缘层以及FEA电阻层。

• The main idea of this paper is to find a way to reduce the work of development of solid modeling for FEA software by exchanging information with CAD software.

  研究的具体思路为：利用专业三维CAD软件进行实体建模，然后通过与CAD软件进行信息交换来得到实体信息并进行实体重现，以找到一种替代实体建模的方法。

• Then, the temperature field is loaded in FEA software to predict thermal stress and deformation.

  并以此温度场为边界条件，利用FEA软件计算了机体热应力和热变形。

• In this paper, the failure of pin punch was analyzed and optimized based on FEA and PVD, according to failure mechanism of fracture and wear of pin punch.

  本文主要利用FEA及PVD技术，针对细小凸模的断裂和磨损两种失效形式，进行失效分析与优化。

• Using ADAMS/FEA module, acting force calculated by ADAMS software program is input FEA program according to load working state.

  运用ADAMS/FEA模块将ADAMS软件计算的作用力按照载荷工况输入到有限元分析程序中。

• Designed using extensive FEA to minimize stresses and maximize component life.

  设计广泛使用FEA来减少重压并使部件寿命达到最长。

• As widely application of FEA in product design and performance, the finite element method is used to analyze the structure of nebulizers based on the piezoelectric coupling theory.

  基于有限元方法在产品设计和性能分析中的广泛应用，根据压电耦合有限元分析理论，对雾化器结构进行了深入的分析。

• The basic principle of FEA for tire was described.

  介绍轮胎有限元分析的基本原理。

• One of the key technique problems is boundary dynamic contact constraint and contact judgment in FEA simulation for 3d complicated massive forming.

  边界界面动态接触约束与接触判断是3维复杂体积成形有限元数值模拟的关键技术问题之一。

• The simulation and analysis of the pressure distribution in head runner of double plex tread extruder were made with ANSYS FEA software.

  采用ANSYS有限元分析软件对胎面双复合挤出机头流道内部的压力场进行模拟和分析。

• The strain energy functions to characterize the mechanical properties of rubber with FEA are described.

  介绍在有限元分析中描述橡胶力学性能常用的应变能函数。

• The FEA model was parameterized by APDL language and the stiffness distribution was computed over the workspace.

  通过APDL语言实现有限元模型的参数化设计，计算出并联机床在工作空间内的刚度分布。

• At the same time, the traditional Hertz contact theory and analyses of experiments are used to prove that the FEA model used in the paper is accuracy.

  同时通过传统赫兹接触理论和试验对其进行验证，间接证明了有限元分析模型的合理性及有限元分析方法的可靠性。

• Based on the heat conduction theory, the FEA theoretical formulas of temperature field and thermal stress are deducted in this paper.

  本论文从热传导原理出发，推导出温度场和温度应力的有限单元法理论公式。

• To the embrittlement phenomenon of steam turbine rotor, this thesis calculated 300mw steam turbine rotor's transient temperature field of cold start-up using FEA method.

  本文针对汽轮机转子的脆化现象，运用有限元方法对引进型300MW汽轮机冷态启动过程的高中压转子瞬态温度场进行了分析计算。

• The thesis is mainly devoted to prove the validity of the design by analyzing the structure of the loading system, via FEA analysis software ANSYS8.0.

  本文的重心是采用有限元分析软件ANSYS8.0对加载系统的结构进行静态分析和模态分析，以验证其设计的合理性。

• This paper integrated the theory, software with the experiment and established a reasonable, proper FEA model.

  本文将理论、软件工具和实验有机结合起来，建立了合适、正确的这种特殊结构的有限元模型。