片语

inlet casing temperature缸温

oil inlet flow temperature进油温度

critical inlet water temperature临界进水温度

inlet air temperature进气温度

inlet manifold temperature进气歧管温度

inlet medium temperature进口介质温度

inlet fuel temperature输入燃油温度

inlet air temperature drop进给空气温度下降

inlet fluid temperature进口温度

inlet oil temperature进油温度

英汉例句

• the system inlet temperature is less than the lower critical threshold.

  系统进气孔温度低于下限临界阈值。

• in this method, the dispersion and overall change of the cavities「frequency can be controlled by changing water flux and inlet temperature of cooling water.

  通过改变水流量和入水温度分别控制加速管各腔频率离散度和整体频率偏移量，实现了使加速管整体频率偏移最小的目的。

• cooling towers」 influence on the inlet temperature of circulating water was also considered to determine optimum running mode of circulating water pumps.

  同时考虑闭式循环水系统中冷却塔对循环水入口温度的影响，确定出循环水泵最优运行方式。

• the world vertical upward flow round critical heat flux experimental database is analyzed based on the slice method, similarity measure, heat balance and inlet temperature verification.

  采用切片法、相似度概念和热平衡以及进口温度检验法，对收集到的圆管垂直向上流动临界热流密度实验数据库进行了分析。

• the calculation example shows that if the inlet temperature of fluid is low and the flux is small, the amendatory value and coefficient are great when the other conditions are fixed.

  计算实例表明，其他条件一定时，流体进口温度越低，流量越小，则修正值和修正系数越大。

• the influences of the angle of tilt and the inlet temperature and concentration and the absorption pressure on the performance of heat and mass transfer are discussed.

  讨论了斜板尺寸和进口温度、浓度及吸收压力等参数对传热传质性能的影响。

• in addition, the length of re-circulation zone decreases slightly with the increase of the inlet temperature in the non-reacting and reacting flow fields.

  另外随着进口气流温度增加，燃烧室冷态和燃烧流场的回流区长度都稍有减少。

• this paper introduces the parameter estimation research for the turbine inlet temperature and compressor exit pressure by using the engine variables measured under the different flight conditions.

  本文研究利用不同飞行状态下测量的发动机变量估计涡轮进口温度和压气机出口压力。

• for rolling dryer, the higher filling power value corresponds to downstream quickly drying way, higher inlet temperature and moisture content.

  对于转筒式烘丝机，采用顺流烘丝方式，较高的来料温度和水分，较大的热风流速，可获得较高的烘丝填充力。

• with the increase of the turbine inlet temperature of high performance aero-engine day by day, the turbine coating blade coating technology has been widely used.

  随着高性能航空发动机涡轮进口温度日益提高，涂层技术在涡轮叶片上得以广泛应用。

• the article analyses the best inlet temperature of false twister in polyester distortion technique by examples.

  通过举例说明在聚酯变形工艺中最佳的假捻器入口温度。

• it is demonstrated for the feasibility that energy saving results may be obtained by reducing inlet temperature of hot oil pipelines.

  以任京输油管道为例，分析了不满输管道节流降耗问题，论证了降低输油管道进站温度的节能效果和可行性。

• table 1 contains the recommended temperature that the heatsink base test point or the air inlet temperature should remain below during the thermal evaluation of a system.

  表1含有进行系统热量测量时散热器基座测试点或空气入口温度应该低于的推荐温度值。

• increasing overall flow velocity and depressing the inlet temperature of cooling water has little effect on improving temperature distribution.

  提高冷却水的总流速和降低进口温度对电池内温度分布的改善作用不好。

• it can be seen that if the engine air inlet temperature is higher and the ambient pressure is lower than the standard conditions , the power output of the effects will be lower.

  可以看出，如果在发动机的进气温度较高，环境压力低于标準的条件下，输出功率的影响将降低。

• reducing the inlet temperature of cooling water and increasing its mass flow are favorable to increase refrigerant performance coefficient, and can decrease optimal pressure at high pressure side.

  降低冷却水进口温度和提高其质量流量不仅有利于提高制冷性能系数，而且能降低最佳高压侧压力。

• a method for gas turbine inlet temperature control is presented, and the effect of this method upon the power output and heat consumption rate of a unit during the performance test is also discussed.

  确保机组在设计的燃机透平进口温度下运行，是进行性能试验时测定机组输出功率和效率的基準条件。

• it is shown from the results that the inlet temperature rise just prior to system instability is approximately linear with the inlet temperature ramp rate.

  数值结果表明，引起失速的进口温升近似地与进口温升率呈线性关系。

• the effects of the cooling water and freezing water inlet temperature are also predicted. the results are reasonable.

  对地下水源热泵机组的性能随着冷却水、冷冻水入口水温的变化情况做了预测，结果合理。

• inlet temperature distortion is one of the key factors effecting engine stability.

  发动机进口温度畸变是影响发动机稳定性的关键因素之一。

• in addition, the variations of the viscous effect with different inlet temperature is studied, the changing law of thrust and thrust efficiency with temperature is analyzed.

  其次，变化来流气体温度，研究粘性效应的变化，分析推力、推力效率受温度影响的变化规律。