片语

planar rake face平面形前刀面

rake&face用耙子耙；扫射 ；搜寻；（树枝或手指甲）刮擦；（用耙子）耙松；（船桅或烟囱）向船尾倾斜；确定（尤指舞台的）倾斜度

curved rake face曲面型前刀面

the rake face前刀面

front face正面，前面

smooth transition of rake face前刀面光滑过渡

convex curved rake face凸曲前刀面

rake face of turning cutter车刀前刀面

convex rake face凸曲前刀面

英汉例句

• Through cutting experiments in which the contact length between chip and rake face of restricted contact cutter is reduced step by step, the variation principle of cutting force is studied.

  通过切削试验，研究了限制接触刀具前刀面的刀—屑接触长度逐渐减小时切削力的变化规律。

• The analysis of thermal damage layer for the rake face can provide theoretical guidances for confirming the machining allowance of surface grinding.

  前刀面热损伤层的定量分析，可以为随动磨削的加工余量提供理论依据。

• The metal in front of the tool rake face gets immediately compressed, first elastically and then plastically.

  在刀具前倾面前的金属直接受到压缩，首先弹性变形然后塑性变形。

• The top view micrographs show the cutting edge and the rake face of the tools.

  俯视显微照片显示了刀具的切削刃和前刀面。

• The rake face normal curvatures of a ball nose end mill in normal direction and chip flow direction are analyzed and calculated in detail in this paper.

  采用微分几何中的曲率分析方法对球头立铣刀前刀面上端刃法线方向和切屑流出方向的法曲率进行了详细的分析计算，并给出了切屑流经前刀面时卷曲半径的计算方法。

• The chip after sliding over the tool rake face is lifted away from the tool, and the resultant curvature of the chip is termed as chip curl.

  滑过刀具前倾面的切屑被提升离开刀具，切屑弯曲的结果被称为切屑卷。

• But most of them are limited in the flat rake face milling insert.

  但是对铣削热的研究大多是对平前刀面铣刀片而进行的。

• The wear form on the rake face is characterized as broad crater, which is directly influenced by the distribution of milling temperature.

  受铣削温度分布的影响，前刀面磨损形态表现为较宽的月牙洼；

• If the friction between the tool rake face and the underside of the chip (deformed material) is considerable, then the chip gets further deformed, which is termed as secondary deformation.

  如果刀具前倾面与切屑(变形金属)底面之间的摩擦相当大，那么切屑进一步变形，这也叫做二次变形。

• Then, the mathematical expression of heat flow density on the tool-chip interface of the rake face is deduced on the basis of milling temperature experiment.

  结合铣削温度试验，推导出了前刀面刀—屑接触面输入的热流密度的函数表达式。

• Oxidation wear appeared at the wear edge of rake face and flank face of cutting tool.

  硬质合金刀具的氧化磨损主要发生在刀具前刀具和后刀面的磨损边缘区。

• By using the profile modeling machining equipment of helix Angle, a new method about grinding rake face of gear cutter hob on tool grinder is presented.

  提出一种用螺旋角仿形加工装置在工具磨床上刃磨齿轮滚刀前刀面的方法。

• It also shows that the chip flow direction is closer to the maximum inclination direction of a rake face with an increase in a normal rake Angle.

  文中还提出，随着法向前角增大，流屑方向将愈接近前刀面最大倾斜方向。

• Based on equation of cutting edges, new geometric model and NC grinding model of rake face of ball end mill with constant normal rake Angle are modeled.

  本文基于刀刃曲线方程，推导了球头等法前角前刀面的几何模型及其数控磨削模型。

• The profiling error of a new type skiving hob with convex curved rake face is analyzed and the change law of profiling error affected by parameters is expounded.

  对新型凸曲前刀面刮削滚刀的理论构形误差进行了全面分析，探讨了各特征参数对构形误差的影响规律。

• Because there exists a chip-curling groove on the rake face, the rake face of a modern cutting tool used on NC machine tool is not a plane, but a curved surface.

  由于现代数控刀具都设计有卷屑槽，从而使其前刀面不是平面，而是曲面。

• Rake Angle. It is the Angle between the face of the tool called the rake face and the normal to the machining direction.

  它是被称为前倾面的刀具面与垂直机加工方向的夹角。

• Our product MMK6026 , which is CNC tool grinder with 6-axis and 5-coordinate controls, is used to machine the rake face and relief of conical ball end mills or other complex shaped tools.

  我们研制的MMK6026六轴五联动CNC工具磨床用于加工锥形球头立铣刀和其它复杂形状刀具的前刀面与后刀面。