片语

reduction achievement ratio复位成功率

reduction n ratio减速比

Reduction success ratio整复成功率

Final reduction gear ratio最终传动减速比

total reduction gear ratio总传动减速比

gross reduction ratio总破碎比

reduction gear ratio减速比

reduction speed ratio减速比

overall reduction gear ratio总减速比

英汉例句

• the speed is based on the synchronous motor speed reduction ratio as a benchmark calculated by dividing the value of.

  转速是以电动机的同步转速为基準除以减速比而算出的数值。

• multi-purpose mini-motorcycle in the belt drive gear for the latter, the main, the size of the driven pulley reduction ratio sub-decision.

  在微型摩托车多用皮带传动方式作后传动装置，主、从动皮带轮的大小决定次级减速比。

• the rational gap length reduced the volume of adhesive effectively and the highest reduction ratio was 60%.

  合理的间隙长度可以有效地减少胶粘剂的用量，减少率最大可达60%；

• the study shows that reduction ratio has a great influence upon lateral metal flow.

  研究结果表明：腹板和翼缘的压下率配比对金属横向流动影响很大；

• the attribute reduction quality, which includes reduction ratio and approximate quality, is defined to scale the reduction effectiveness.

  提出约简质量的定义，从属性约简率和近似质量两方面来衡量约简效果。

• so, in order to harmonize the elongation coefficient of web and flange and to avoid the rolling defects, the reduction ratio of flange should be larger than that of web.

  为使腹板与翼缘延伸一致，避免轧制过程中出现缺陷，翼缘的压下率应大于腹板的压下率。

• in the mini-motorcycle multi-way for the latter with a belt drive transmission, primary, secondary driven pulley reduction ratio of the size of the decision.

  在微型摩托车多用皮带传动方式作后传动装置，主、从动皮带轮的大小决定次级减速比。

• the influences of strip thickness, forward and backward tension, reduction ratio and resistance to deformation on the edge drop were investigated in detail.

  详细研究了带钢厚度、张力、压下率、变形抗力等对边缘降的影响。

• this thesis studies the effect of wide—high ratio, bump ratio and reduction ratio on the skew ratio in plain roller rolling square bar through simulated hot rolling steel by steel roller rolling lead.

  通过钢辊轧制铅件模拟热轧钢件，研究了平辊轧制矩形件过程，轧件的宽高比、鼓形比和压下率三个参数对脱方的影响。

• the hot-continuous-rolling technics under small reduction ratio has a close relationship with the billet quality control and the hot(red) sending process control and the cooling control after rolling.

  小压缩比热连轧生产与铸坯质量控制，热（红）送过程控制以及轧后冷却控制密不可分。

• in this paper, the method measuring joint reduction ratio of v01 arc welding robot is presented.

  提出了v01弧焊机器人关节减速比的测量方法。

• in determining the main reduction ratio , the drive axle of the mechanical and structural analysis, and calculated the school.

  在确定了主减速比之后，通过对驱动桥的力学和结构分析，进行计算校和。

• lung-mediation reduction ratio of air type indicate squamous cancer strongly.

  含气型肺、纵隔窗缩减率高度提示肺腺癌。

• cylinders with inner ribs are shaped in one pass using big thickness reduction ratio or use different mandrels to realize the preliminary shape and the final forming.

  带内筋筒形件采用大减薄率一道次成形或采用不同的芯模实现预成形和终成形；

• tolerance of wheat varieties to insect injury was determined with ratio of aphid numbers and reduction ratio of wheat weight per 1000 grains.

  用蚜量比值和千粒重降低比值法测定了小麦品种的耐害性。

• the experiment results, show that the range of reduction ratio is very practicable.

  理论计算结果与实验结果对比表明，所得减薄率选取范围具有较强的实用性。

• results indicate the local high point height and additional tension stress of rolled strip are proportional to local high point initial height of strip, decrease as rolling reduction ratio increases.

  研究结果表明：轧后带钢局部高点高度及附加张应力的大小与来料高点高度成正比，随总轧制压下率的增大而减小。

• through the comparison of numerical simulation value and experiment results, the range of reduction ratio was obtained while the tube forming ideality.

  通过数值模拟与实验结果的比较，得出了获得较理想的成形薄壁筒形件时减薄率的选取范围。

• these factors include ratio of upper and lower roll diameter , reduction ratio , enterance angle and roll rotation speed.

  因素有上下轧辊直径比、压下率、导入角和轧辊转速。

• experiments show that this approach can achieve high energy reduction ratio by exploiting the dynamic slack time sufficiently and controlling the scaling overheads effectively.

  实验结果表明，该方法能够充分利用动态松弛时间，有效控制调整开销，实现较高的能耗优化率。

• the influence of magnitude of the reduction ratio on the products quality was studied.

  并对钼方坯旋锻归圆前道次压缩比的大小对钼产品质量的影响进行了研究。