片语

ring-groove cylindrical shell环向槽圆柱壳

o-ring seal grooveO型密封圈槽

Ring narrow groove环形窄槽

seal ring groove密封环槽

cold ring rolling groove冷辗扩模具

retaining ring groove扣环槽

fire ring groove防火环槽

ring and groove joint环槽接合

ring groove side环槽侧

英汉例句

• The piston rings carried in the ring groove are of two basic types: compression rings and oil-control ring.

  安装在环槽中的活塞环有两种类型：压缩环和机油环。

• The insulating rubber sealing layer is stuck on the surface of the unidirectional weftless tape banding layer for the commutator. The ring groove is arranged at the end of the commutator plate.

  所述的换向器在无纬带绑扎层表面粘接有绝缘胶泥密封层，在换向片端部有一环状沟槽。

• The use of a snap ring inserted in the snap ring groove in the outer ring provides a particularly economic and axially space-saving arrangement (FIG 4).

  采用插入外圈卡环槽内的卡环可以组成特别经济、节省轴向空间的配置(图4)。

• Piston is a key component in an engine, working conditions is very poor, ring groove and head section are prone to appear abrasion wear and fracture failure due to sever impact and friction.

  活塞作为发动机的重要部件，工作环境恶劣，环槽和头部由于剧烈的沖击和摩擦容易出现严重磨损甚至断裂而导致失效。

• Outer ring groove of curvature of the center and bearing center consistent, so with automatic self-aligning ball bearing the same tone heart function.

  外圈滚道面的曲率中心与轴承中心一致，所以具有与自动调心球轴承同样的调心功能。

• The laser heat treatment process and mechanism on the surface of piston ring groove were studied.

  对活塞环槽表面的激光热处理工艺与机理进行了试验研究。

• Two groove of the inner ring and outer ring groove for the ball between the form of a drum, equipped with roller bearings.

  二条滚道的内圈和滚道为球面的外圈之间，装配有鼓形滚子的轴承。

• Time for the third kind of closing well is so long that flange steel ring groove on the top of casing-head is heavily corroded in M4 well being situated in Tarim basin.

  位于塔里木盆地的M4井，由于三类封井时间较长，造成套管头上部法兰钢圈槽严重腐蚀。

• The ceramic treatment for the first ring groove of ZL108aluminum alloy piston was conducted with micro-arc oxidation technique.

  利用微弧氧化技术对ZL 108铝合金活塞第一道环槽进行了陶瓷化处理。

• The dimensions of the snap ring groove and of the chamfer adjacent to the groove (fig 20) are in accordance with ISO 464:1995, which also specifies suitable snap ring dimensions.

  止动槽和紧邻的倒角（图20）尺寸符合1995年的ISO464标準，该标準还规定了适当的止动环尺寸。

• Out in the shaft loaded oil ring groove or by centrifugal force along the axis of the oil drain off the surface, the oil flows back to the assembly after the pool, and thus play a role in sealing.

  在轴上开出沟槽或装上油环，借离心力将沿轴表面外流的油甩掉，集结后流回油池，因而起到密封的作用。