片语

Tear Strength-prop撕裂强度

High tear strength系列

Tear Strength KN撕破强力

tear resistance撕裂强度；撕裂测试；撕破强度

Trapezoidal Tear Strength梯形撕裂强度

Tear Resistance Strength抗撕裂强度

Tear Tensile Strength撕裂拉伸强力

ballistic tear strength沖击撕裂强力

tear r strength撕裂强度

英汉例句

• it has a better flex cracking resistance than those of natural rubber but a lower tear strength and a higher dynamic modulus.

  它比天然橡胶具有较好的抗挠曲开裂性能，但撕裂强度较低，动态模量较高。

• the fkm/nbr blend was prepared by dynamic vulcanizing method. the compound had higher tear strength at 150℃.

  采用动态硫化的方法制备了fkm/nbr的共混胶，该胶料在150℃下具有较高的撕裂强度。

• the finished leathers had good fullness and dyeing performance as well as higher tensile and tear strength which were obviously better than that of traditional chrome leather.

  革坯染色性能优良，丰满性良好，其抗张强度、撕裂强度均能明显高于普通铬鞣革；

• in this paper, we will take tear strength for example to discuss this correlation.

  物理性能参数间存在着相互关系，该文将以撕裂强度为例对其进行探讨。

• there lie some correlations among mechanical properties. in this paper, we will take tear strength for example to discuss this correlation.

  物理性能参数间存在着相互关系，该文将以撕裂强度为例对其进行探讨。

• some tear testing methods and standards used for architectural membrane materials by overseas manufacturer are compared. the influences of testing conditions on tear strength of samples are analyzed.

  比较了目前国外用于测试膜材料撕裂强度的主要方法和标準，分析了不同测试方法对膜材料撕裂强力的影响，讨论了膜材料的撕裂机理。

• r and high frost - line in order to make the films have proper longitudinal tear strength ( md) and horizontal tear strength (td).

  试验发现：为保证合适的薄膜纵向撕裂强度和横向撕裂强度，应在高牵引速度、大吹胀比和高起霜线的条件下进行该树脂的加工。

• the introduction of or into sbr and nr enhanced their hardness and tear strength .

  纳米累托石的加入可以显着提高sbr和nr的硬度和撕裂强度。

• in this paper, research on curing system of vulcanized silicone rubber aging tear strength after impact.

  本文主要研究论述硫化体系对硫化硅橡胶老化后撕裂强度的影响。

• the results showed that by replacing aromatic oil with petroleum resin at reduced weight, the processing safety improved, tear strength of the vulcanizate and h pull-out force increased;

  结果表明，以石油树脂减量替代芳烃油，胶料的加工安全性提高，硫化胶的撕裂强度和h抽出力增大；

• the mechanical experimental results showed that pva had a little effect on the tensile strength, right angle tear strength and elongation at break, and…

  力学性能测试结果表明，加有pva的pe防雾膜在拉伸强度，直角撕裂强度，断裂伸长率等方面比未加pva的防雾膜要小，但不影响其使用性能。

• hydrolysis: water and high temperature can change the consistency of certain polyurethanes. colours change and material crumbles into small pieces. tensile and tear strength deteriorate.

  水解：水和很高的温度可以改变一定的聚氨酯类韧性。颜色改变和原料分成小块，张力和撕力会破坏。

• consider the bursting strength that is required and the tear strength desired.

  考虑爆破强度是必需的，所需的撕裂强度。

• the results showed that the tensile strength, elongation at break and tear strength increased with the ommt content increasing.

  测试结果表明，随着蒙脱土用量的增加，复合材料的定伸应力、拉伸强度和撕裂强度均大幅度提高。

• it was shown that mlpb could improve the interface combination between the organic fillers and the rubber matrix, and could increase the tear strength and the stickiness of the iir rubbers.

  研究表明，mlpb能在一定程度上提高有机填料与橡胶基体之间的界面结合强度； 同时，也能有效地提高iir胶料的自粘性能和撕裂强度等性能指标。

• rdh bleached pulp had relatively higher tear strength and lower tensile strength compared with traditional bleached sulfate pulp.

  两种漂白浆相比，rdh漂白浆具有相对较高的撕裂强度和较低的抗张强度。

• the cause leading to deviation of tear strength in measuring tear strength of silicone rubber vulcanizate was analyzed.

  分析了在热硫化硅橡胶混炼胶撕裂强度的测试中撕裂强度出现偏差的原因；

• next mold will be made from high tear strength rtv for sure.

  模具明年将作出从高撕裂强度室温硫化肯定的。

• ldpe (low density polyethylene): offers such advantage as tear strength and high chemical resistance. it is also waterproof.

  ldpe（低密度聚乙烯）：具有以下优良性质：高撕裂强度，高耐化学性，防水性。

• it is mainly used as rubber reinforcement and filler, to improve their elongation, tear strength and resistance to abrasion.

  主要用作橡胶制品的补强剂和填充剂，能明显改善橡胶制品的抗拉强度、抗撕裂性和耐磨性。

• silicone tubing has some limitations, including lower tear strength when compared with pu tubing.

  硅胶管有一些限制，包括降低撕裂强度相比，pu管。

• the physical indices such as tensile strength, elongation and tear strength before and after the dye-fixation were tested.

  并且对固色前后断裂强力、伸长、撕破强力等物理指标进行了测试。

• methods: the water sorption, the water solubility and the tear strength of two kinds of silicon rubbers were examined and evaluated under the same conditions.

  方法：在相同条件下对两种硅橡胶材料进行吸水率、溶解率及撕裂强度测定，对其进行t检验分析。