英汉例句

• the adhesion strength and stripping and splitting prevention measure were also discussed.

  同时研究了涂料的粘附强度、防裂、防剥落等措施。

• the fracture of the pins was caused by improper assembly flow and lower adhesion strength of the fixing glue.

  装配方式不合理，固定胶粘接强度不足和工艺不完善是导致引脚断裂的原因。

• and the calculating formula of adhesion strength of film-matrix is established in the paper.

  还建立了四点弯曲法定量计算膜基结合强度的公式。

• the influence of filler on extensibility, elasticity and adhesion strength of film, and influence of environment temperature on coated film surface dry time are studied.

  研究了填料对膜延伸性、弹性、粘结强度的影响，环境温度对涂膜表干时间的影响。

• adhesion strength of diamond films on cemented carbide were evaluated by rockwell indentation tests.

  扫描电镜观察表面金刚石形貌，洛氏硬度压痕法评价涂层结合情况。

• the adhesion strength development between pcm and commencement mortar has been studied in this test.

  本文研究了聚合物水泥砂浆（pcm）与普通水泥砂浆之间的粘接强度。

• this tester can test tensile, tearing, peeling, adhesion strength and other resistant properties of various materials, with elongated value (extensibility) display.

  本机可测各种材料之拉力、撕裂、剥离、粘接力…等抗力物性，附有伸长量（延伸率）显示屏。

• the sample was characterized by melt flow rate and adhesion strength to aluminum.

  用熔体流动速度和粘结强度表示试样的特征。

• the results showed that above non-tire items using nr/br/sbr blends had better scorching, processability and fiber adhesion strength than those of using nr/br blends.

  实验结果表明，上述各制品胶料与nr／br共混胶制品胶料相比，前者在焦烧性能、工艺性能以及化学纤维粘附强度等方面均优于后者。

• the results show that the interfacial adhesion strength increased noticeably for composites of active aramid fiber but the fracture energy of the interface decreased.

  实验结果证明，芳纶表面改性显着提高了其复合材料界面的粘结强度，相反却降低了其界面断裂能。

• in another embodiment, at least one component exhibits interlayer adhesion strength similar to vinylidene chloride polymers.

  在另一实施方案中，至少一个组件表现出与偏二氯乙烯聚合物类似的层间粘合强度。

• a wedged load test method was used to evaluate the adhesion strength of hard coatings.

  提出用楔形加载法评价高强度涂层材料与基体的结合强度。

• the effects of depositing temperature on the thickness, adhesion strength and hardness of tin film have been studied in this paper.

  研究了沉积温度对膜层的厚度、结合力及硬度的影响。

• the four-point-bending method is a comparatively ideal method to evaluate the adhesion strength of vapor deposited film to matrix is given in this paper.

  本文指出四点弯曲法是定性分析和定量计算气相沉积薄膜与基体结合强度的较理想的方法。

• the designer should consolidates the experience, adopt the formula rationally and calculate the internal-power, compressive and adhesion strength accurately.

  工程实践中，设计者应当总结经验，对锚筋内力、桩承载力和粘结力采用合理公式并準确计算。

• the matrix of chinese medicine patcher was studied by uniform design and taking adhesion strength as index.

  采用均匀设计法，以粘着强度为指标，筛选中药巴布剂基质。

• during the molding and storing process, humidity is the foremost factor affecting the characteristics of htpb propellant grain and adhesion strength between interfaces.

  在成型及贮存过程中，湿度是影响丁羟推进剂药柱性能及各界面的联合粘接强度的首要因素。

• the effect of monomer ratio, the kind and concentration of keying agent on adhesion strength is also studied.

  研究了单体配比、 增粘剂种类、增粘剂用量对剥离强度的影响。

• the adhesion strength between the dyes covered aluminum foils and pvc can be enhanced significantly by polyester adhesive added modified organic silicon coupling agent.

  通过在聚酯胶粘剂中使用改性有机硅偶联剂，可以改善着色铝箔与pvc的粘结性能。

• the effects of the content of foaming agent as well as the kinds and content of foam stable agent on the foamability and the adhesion strength were investigated.

  考虑了发泡剂用量、泡沫稳定剂种类及用量对发泡倍率和粘接强度的影响。

• the contact angles decrease, the roll angles increase, the antifouling performance gets small and the adhesion strength increase with the increment of space of the microstructure.

  随着微结构间距的增大，接触角减小，滚动角增大， 抗附着性能降低，附着强度增大。

• the sbs thermoplastic elastomer was melted to react with maleic anhydride(mah), methacrylate (mma), and the mixture of mah and mma respectively to improve sbs adhesion strength to metal.

  通过熔融接枝以马来酸酐（mah）、甲基丙烯酸甲酯（mma）或mah/mma混合单体对丁苯热塑性弹性体（sbs）进行改性，以改善与金属基材的粘接性。