片语

adhesive bonding strength粘结性能

adhesive shearing strength粘接剪切强度

adhesive bond strength tester粘合强度试验机

adhesive joining strength粘接强度

tensile adhesive bond strength粘结抗张强度

adhesive shear strength粘接剪切强度

adhesive tensile strength粘结抗拉强度

adhesive e strength胶粘强度

英汉例句

• this resin is a kind of perfect adhesive which has high adhesive strength and good thermal resistance, can resist corrosion from all organic solvents and can resist acid and alkali.

  该树脂是一种粘结强度高、耐热性好、能抵抗所有有机溶剂的腐蚀、能耐酸堿的理想粘结剂。

• the average reliability of defects classification is over 80%, and the estimation of adhesive strength is satisfactory.

  胶接缺陷的平均识别率在80%以上，胶接强度的估计精度也令人满意。

• it was proved that high velocity arc spraying ni-al coating is one of best intermediate coatings with high adhesive strength and fine structure.

  高速电弧喷涂镍铝涂层结合强度高，涂层组织致密，是优良的打底涂层。

• the soil adhesive strength is mainly composed of capillary pressure and viscous resistance of the water film, which are affected by the nature of solid surface.

  土壤粘附强度主要由毛细管作用力和界面水膜粘滞力构成，固体表面性质对其产生影响。

• the results of this paper have shown that it is successful for improvement on the water proof and adhesive strength of pvf with tdi.

  研究表明甲苯二异氰酸酯对聚乙烯醇缩醛胶粘剂耐水性改性是可行的并且能提高胶粘剂的粘接强度。

• the effect of micro-arc voltage on the microstructure and adhesive strength of the films was studied, and the bioactivity of the films was also evaluated.

  研究了电压对膜微观结构和结合强度的影响，并评价了微弧氧化钛膜的生物活性。

• the relationship between brookfield viscosity and temperature, dip pick-up and adhesive strength of dip solution for pa6 tire cord was discussed.

  讨论了锦纶6帘子布浸胶液布氏粘度与温度、附胶量、粘着强度的关系。

• a liquid used together with 3% b powder. for rough surface treating of rubber. enhance adhesive strength of pu adhesive to rubber.

  液和b粉，按一定比例3%配合，涂布于磨粗后的橡胶表面，提高pu胶对橡胶的粘合强度。

• the result indicates that improving measurements regarding to physical and chemical factors involved with adhesive strength can reinforce adhesive strength to some extent.

  结果表明，结合影响粘接强度的物理和化学因素作出针对性的改进措施，可在一定程度上提高接头粘接强度。

• the mechanism of generating freezing adhesive strength was analyzed, providing a new approach to the research of anti-freezing adhesive theory and techniques.

  分析了材料的冻黏强度机理，为冻黏防治理论与技术研究提出了新的途径。

• in this paper, the influence of process parameters of blasting pretreatment and arc spraying on coating「s adhesive strength is studied.

  分析了喷砂预处理和电弧喷涂这两个过程的工艺参数对涂层的结合强度的影响。

• the effects of coupling agent, filler and toughening agent on adhesive strength were also studied.

  还研究了偶联剂、填料和增韧剂等对粘接强度的影响。

• the influence of the kinds of epoxy resin, the proportion of composite curing agent , and the content of accelerant on the adhesive strength and heat resistant properties of adhesive were discussed.

  重点讨论了环氧树脂种类、复配合固化剂比例以及促进剂用量对胶粘剂粘接强度和耐热性能的影响。

• after the carbon fiber」s surface treated, the interfacial adhesive strength of the composites increased greatly and the effect of treating with acetone is better than that with heat.

  碳纤维布经过表面处理后与聚苯硫醚的粘接强度大大提高，其中用丙酮浸泡的效果好于高温热处理；

• the effect of kinds of polysiloxane coupling agents, different treatments on the adhesive strength has been investigated by using shear adhesive strength and sem.

  利用剪切粘接强度、sem等方法，考察了有机硅烷偶联剂的种类和处理方法对丙烯酸酯类胶粘剂，粘接强度的影响。

• a industrial production process of urea-formaldehyde resin adhesive with high adhesive strength and low free formaldehyde content was presented.

  介绍一种含游离甲醛低的粘接强度大的工业生产脲醛树脂粘合剂的方法。

• this paper deals with the adhesive state of amorphous ni p alloy plating using impact fracture test method and also measuring the adhesive strength of the plating quantitatively.

  用金相沖击断口法研究了化学沉积非晶态镍磷合金层与基体的结合状况，并用扭转法定量测量了化学沉积合金层的附着强度参数。

• the factors affecting the adhesive strength between silicone rubble and aluminum during the course of manufacture of new hot printing plate were investigated.

  研究了新型烫印版制备过程中影响硅橡胶与铝板之间粘结强度的因素。

• if the amount of vinyl acetate latex is 1%, it will effectively improve the adhesive strength of produced coating.

  醋酸乙烯乳液分散剂可有效地提高涂料的粘结强度，其最佳量为涂料的1%。

• stable spraying process and uniform and compact coating with high adhesive strength can be obtained by using the expert controller.

  研制的等离子喷涂专家控制器可实现对常用喷涂粉末的稳定喷涂并获得均匀致密和高结合强度的等离子涂层。