片语

axial hydraulic thrust[机]

axial hydraulic thrust load轴向水推力

axial of thrust沿推力作用线分布的

axial l thrust load轴向推力负荷

axial l thrust bearing轴向止推轴承

axial post thrust轴向后推力

axial l thrust轴向推力

axial negative thrust轴向负推力

axial water thrust轴向水推力

英汉例句

• The variation laws of axial thrust with flow rate are found.

  得到了轴向力随流量变化的规律。

• This research dealt with the axial thrust and the wearability of graphite bearing of a vertical canned motor pump, which are the two critical problems about the pump「s working life.

  对影响立式屏蔽泵使用寿命的两个关键问题——泵的轴向力和石墨轴承的耐磨性进行了研究。

• Repelling vanes shall be provided on the top shroud to expel solids and reduce axial thrust and pressure at the seal area.

  在泵顶部应该配置排斥叶片，用于排出固体颗粒，减少轴向推力和密封区域的压力。

• Using of impulse section blade ensured its flow capacity with the axial thrust almost unchanged.

  在保持轴向推力几乎不变的情况下，选用沖动式叶片保证了叶片有较好的通流能力。

• Individually sized for pressure break down, and axial thrust balance.

  个别中小企业的压力分解，并轴向推力平衡。

• This paper presents the key technical points in increasing the capacity of an industrial turbine, such as steam flow, rotor strength, axial thrust and auxiliary equipments.

  具体阐述提高工业汽轮机能力需考虑的主要技术问题：蒸汽流量，转子强度，轴向推力及辅助设施。

• Whole model of impeller clearance and labyrinth seal are built up, and the effect of seals with two sides of impeller to axial thrust is considered fully.

  建立了叶轮间隙和迷宫密封的整体模型，并充分考虑了叶轮两侧密封对轴向推力的影响。

• The axial thrust of the propeller is the force working in a fore and aft direction.

  在螺旋桨的轴向推力，是部队在向前或向后方向努力。

• It can turn the axial thrust on the whole pipe.

  在工作是可以反轴向推力传递至整个管道。

• The MSH range is designed for high pressure applications and the axial thrust is balanced by the combination of the drum and disc.

  MSH系列产品作为针对高压应用的设计，轴向推力通过平衡室系统和圆盘一起进行平衡。

• It is shown that due to the presence of axial thrust and the gradual cracking of the section, a plain concrete element can deform significantly without losing its flexural strength.

  论证了由于板中存在推力以及截面的逐渐开裂，素混凝土构件能显着变形而不(？)其承载能力。

• With an additional axial thrust bearing, both the thrust and radial bearings are preloaded individually.

  由于增加了一套轴向止推轴承，所有的推力和向心轴承均被分别预加载。

• It」s necessary to calculate the pressure distribution in the space between. the centrifugal impeller and the case for calculating the axial thrust of high pressure centrifugal pumps and compressures.

  计算高压离心式水泵、压缩机转子流体轴向推力时，需要计算叶轮侧隙中流体压强的分布。

• The tapered roller bearing replaces axial thrust ball bearing.

  采用圆锥滚子轴承取代现有的轴向推力球轴承。

• Bear the load direction is mainly not the same, the main bearings to the heart to bear a larger part of a smaller radial load and axial load to bear large axial thrust loads and a smaller radial load.

  主要是承受载荷方向不一样，向心轴承是主要承受较大的径向载荷和一部分较小的轴向负荷，推力是承受较大的轴向载荷和较小的径向负荷。

• Moreover, a gear pair with curvilinear - tooth traces operates without axial thrust force.

  除此之外，具有曲线型齿线之齿轮在运转时亦不会产生轴向的推力。

• Other design methods were also presented, such as the face seal at inlet, axial thrust bearing, and its effect to pump efficiency was also discussed.

  同时进行了进口端面密封设计、推力轴承设计以及对水泵效率影响的讨论。