英语释义

1. symmetric in respect to an axis

片语

axisymmetric forebody轴对称头体

axisymmetric shell轴对称壳体

axisymmetric delamination轴对称脱层

axisymmetric problem[数] 轴对称问题

axisymmetric aspheric轴对称非球面

axisymmetric sheet适用于板料轴对称

axisymmetric extrusion轴对称挤压

axisymmetric flow[流] 轴对称流（等于axial flow）

axisymmetric torus轴对称圆环

英汉例句

• on the basis of the theory of dynamic mechanics and elastic-plasticity mechanics, the asphalt pavement of semi-rigid subbase on the soft clay ground is analyzed using the axisymmetric fem.

  基于动力学和弹塑性力学理论，采用轴对称有限单元法系统地分析了软土地基上半刚性基层沥青混凝土路面结构体的工作性状。

• the finite element method was employed to study the micromechanics in rubber toughened epoxy resins using the axisymmetric model contained a rubber and a hole.

  使用包含一个橡胶和空穴的轴对称模型的有限元计算来分析橡胶增韧环氧树脂细观上的力学行为。

• the method can be extended to axisymmetric and three-dimensional turbulent boundary layers if the pressure gradient effect is considered.

  如果考虑压力梯度的影响，还可以将该方法推广到轴对称和三维湍流边界层中去。

• similarly, when our life is directly, we can rule of life is in the peak, the two curves can be a perfect axisymmetric graphics.

  同样，当我们的人生处于低谷时，我们的生活準则可以处于高峰，这两条曲线可以成为一个完美的轴对称图形。

• in this paper, displacements and stresses of multilayered anisotropic soil layers under axisymmetric surface loading are derived by use of initial function method.

  本文推导了多层各向异性地基在轴对称表面荷载作用下的位移和应力的初参数解法。

• the failure forms of rock materials in axisymmetric compression are studied based on the discontinuous bifurcation theory, and a set of experimental data of marbles are simulated.

  采用不连续分叉理论，分析了轴对称状态下巖石材料的破坏形式，并采用一组大理巖的实验结果进行了模拟计算。

• the flash butt welding parameters of axisymmetric 45 steel were determined utilizing the orthogonal test.

  利用正交试验法确定了45钢的闪光对焊轴对称件焊接工艺。

• firstly, seal ring can be simplified as two axisymmetric independent models, and the finite element method is used to solve the problem of the temperature field and stress field of seal ring.

  首先本文基于有限元模型，将机械密封动静环简化为两个独立的轴对称模型，用有限单元法求解其稳态、瞬态温度场及热应力场的数值结果。

• the influence coefficient matrix of the linear axisymmetric triangular element and the input vector expression are derived.

  推导了轴对称线性三角形元的影响系数矩阵和输入向量公式；

• finite element analysis of head/disk continuous sliding contact was performed to investigate temperature field and thermal stress field due to frictional heat using an axisymmetric thermal model.

  采用二维轴对称有限元模型计算磁头/磁盘滑动接触下，铝质磁盘的稳态温度和热应力场以及热退磁临界条件。

• by the use of the continuity conditions at the layer interfaces, the general solution formulation of multilayered axisymmetric space piezoelectric media is given.

  根据层间完全接触的连续条件，由传递矩阵方法导出了多层压电材料空间轴对称问题的一般解析式。

• the axisymmetric instability of tokamak equilibria with a shaping coil system is studied using the energy principle.

  本文应用能量原理研究成形线圈系统托卡马克平衡的轴对称不稳定性。

• a two-dimensional axisymmetric finite element model of sampling tube and sediments is built.

  建立了取样管与沉积物接触的二维轴对称有限元模型。

• considering axisymmetric motion in the pile, the frequency equation for longitudinal modes is derived herein.

  针对轴对称情况，推导了纵向模态的频率方程。

• giving up any assumptions about displacement models and stress distribution, the state equation for the axisymmetric problems of thick closed laminated cylindrical shells is established.

  抛弃任何有关应力或位移模式的人为假设，在轴对称情况下，对强厚度叠层闭口柱壳建立其状态方程。

• solves the problem of boundary value on an annular crack by using the nonlocal stress solution of an axisymmetric crack problem and approximative method of series expansion.

  利用已得到的三维轴对称问题的非局部弹性应力的解，采用级数近似展开的方法，求解环状裂纹的边值问题。

• in this paper the deformations and stability in large axisymmetric deflection of spherical caps under centrally distributed pressures are investigated.

  本文研究圆底扁薄球壳在中心分布压力作用下的轴对称大挠度变形和稳定性。

• briefly introduces the finite element model of axisymmetric field and the results of magnetic field calculation in metal.

  介绍了轴对称场的有限元模型及其用于计算金属内部磁场分布的结果。

• the dispersion equation of structure acoustic coupling system for fluid filled pipes surrounded by elastic media under axisymmetric motion was derived from shell dynamic equation.

  从壳体基本运动方程出发，导出了弹性介质中的充液管道在轴对称运动下声振耦合系统的频散方程。

• at present, some ductile fracture criteria are applied only to predict the forming limit in stamping forming of simple axisymmetric part.

  目前已提出的韧性断裂準则预测板料成形极限，只在简单轴对称件中得到应用。

• through computation of axisymmetric shells, some useful conclusions are drawn.

  计算了轴对称壳获得了一些有益的结论。

• the process of axisymmetric drawing of anisotropic materials is considered.

  研究了轴对称拉伸各向异性材料的过程。

• under axisymmetric condition, the solution can be represented by legendre functions.

  在轴对称情况下，此解可以由勒让德函数所表示。

• in this paper rapid distortion theory is used to predict the effect of anisotropy on the structure of shear free boundary layer and axisymmetric straining turbulence.

  本文运用湍流快速畸变理论对各向异性条件对无切变边界层及轴对称应变湍流特性的影响进行了探讨。

• in this paper, a general analytical solution for the axisymmetric bending of a semispherical shell with simple support is presented based on the three-dimensional elasticity.

  本文用三维弹性力学理论求得简支半球壳轴对称弯曲问题的一般解析解。