英语释义

• cut a bevel on; shape to a bevel;

  "bevel the surface"

• two surfaces meeting at an angle different from 90 degrees

• cut a furrow into a columns

片语

chamfer edges去角缘

chamfer line去角线

Chamfer Entities倒角

CHAM Chamfer斜面

Chamfer Feature倒角特征

inclined plane[力] 斜面

chamfer cutter倒角铣刀

Chamfer Offset倒角偏移

decline下降；衰落；谢绝

Chamfer Box斜切立方体；倒角长方体

Curve Chamfer曲线倒角

英汉例句

• the length of chamfer shall be between1 and2 complete threads as measured parallel to the axis of the threaded component.

  当平行于螺纹构件轴线方向进行测量时，倒角长度应该在1-2全螺纹扣之间。

• of flat glass products for the grinding. glass straight double-edge of the cumo, jingmo chamfer on both sides of the cumo and one-time processing can be completed.

  产品适用于对平板玻璃的磨削。玻璃双直线平边的粗磨、精磨及两侧倒角的粗磨可一次性加工完成。

• this article introduces special purpose device for working procedure inspection that solves the problem of quick measurement of bigger diameter hole「s chamfer depth.

  介绍一种用于工序间检测的专用装置，解决直径较大孔的倒角深度的快速测量；

• as to whether it will therefore let you cannot secure, you jumped chamfer whether to solve problems, whether more happy, that, they tube to reach.

  至于是否会因此让你不能安心，你跳了槽是否解决问题，是否更加开心，那个，他们管不着。

• chamfer : the flat surface formed by cutting away the sharp edges of two meeting surfaces.

  倒角：两个表面相交处，通过切掉尖锐边缘形成的平面。

• in addition to check and adjust parts automatic spring coiling machine is a sensitive, chamfer parts processing in place and so on.

  另外还要检查自动卷簧机的调节部位是否灵敏，零件的倒角部分是否加工到位等等。

• but for reminder: the dimensions related to big chamfer are not major characteristic.

  但提醒：大倒角的尺寸并不大特点。

• the cause and mechanism of valve failure are analyzed, and the method of tumbling chamfer is studied to improve service life of the valves.

  综合分析了阀片的失效原因、机理，并进行了对阀片边缘实施滚磨倒角来提高其疲劳寿命的实验研究。

• next, chamfer the part so that it appears as the drawing.

  下一步，倒角的一部分，所以它似乎作为绘图。

• in this paper, the author introduced the accuracy design of chamfer edge of spline gear hob and the calculating method when designing parrallel side spline gear hob.

  本文介绍在设计矩形花键滚刀时，花键滚刀倒角切削刃的齿形角和起始点的精确设计与计算方法。

• table 1 – accepted deiation for linear measurement except for chamfer edges.

  表1---除倒角外，所有线性尺寸的公差标準。

• a milling hole main shaft, the chamfer main shaft and a main electric motor are all installed on a revolution body.

  铣孔主轴、倒角主轴和主电机均安装在回转体上。

• rechamfer : defect on radii and chamfer; defective chamfer such as nicks that are considered to be repairable.

  重新倒角：可被重新修复的倒角缺陷，例如划痕。

• then i added a smoothing modifier to clear unwanted smoothing」s and then a quad chamfer modifier on top to get chamfer for all edges.

  然后我进行了平滑修饰，将所有我不想要的弧线去掉，最后在四个斜面顶部进行修饰，得到所有的边缘倒角。

• the cutting rotational speeds of the milling cutter of the milling hole disk and the chamfer disk milling cutter are transmitted by the respective gear of the main electric motor.

  铣孔盘铣刀和倒角盘铣刀的切削转速由主电机经各自的齿轮传动传入。

• after the part is complete chamfer all corners and relieve all burs.

  部分完成后，倒角的各个角落，减轻所有鉆。

• if you need the capability study on the big chamfer for 300 pcs, then we have to measure at cmm(3d) as gft method.

  如果您需要300个大倒角能力的研究，那么我们在三坐标测量机（3d）测量gft的方法。

• select those front edges and chamfer them then click apply and chamfer it again but this time with a lower value.

  选择前面的边并倒角，然后单击应用并以较低的值再次倒角。