片语

outer curvature radius外部曲率半径

wavefront curvature radius波面曲率半径

minimal curvature radius method最小曲率半径法

curvature radius of waterway航道弯曲半径

tunnel curvature radius隧道曲率半径

curvature radius of channel航道曲率半径

first curvature radius第一曲率半径

groove curvature radius沟道曲率半径

spherical curvature radius球面曲率半径

英汉例句

• We have made certain that the reason of the splined spindle rapture is fatigue failure, its crack initiation lies in the minimal knuckle curvature radius surface region of the spline dedendum bottom.

  初步确定了花键轴的断裂是疲劳断裂，裂纹源在花键齿根底部过渡圆角曲率半径最小的表面部位。

• In higher pair plane transmission, it is important to determine the curvature radius of the member.

  平面高副传动中，如何确定高副元素的曲率半径是一个很重要的问题。

• The influence of temperature, curvature radius of lens and the thickness of oil on ultrasonic field is analyzed.

  并分析了温度、透镜曲率半径和油层厚度对探头声场的影响。

• 2 the curvature radius and the change curve of the transition fillet at the shoulder of the input shaft of the reducer are not carefully considered.

  2减速机输入轴处轴肩处未细致考虑过渡圆角的曲率半径和变化曲线使应力集中严重发生疲劳破坏。

• In the production practice, this problem should be kept in mind and resolved by programming for compensating the variation of tool nose curvature radius and removing the error.

  在实际生产中要加以注意，并通过编程以补偿刀尖圆弧半径的变化，消除误差，使问题得以解决。

• In track simulation, the corresponding earth equivalent radius of a track in a specific range is approximate to the earth curvature radius of the latitudinal location of the target.

  介绍了在航迹模拟中，一条航迹在一定范围内对应的地球等效半径，可以近似为目标所在的纬度的地球曲率半径。

• The results show that the small curvature radius on HT250 surface were removed by melted or evaporation, finally a flat finishing metal surface was obtained.

  结果表明，经微等离子弧处理的HT250表面，曲率半径小处全部发生熔化和蒸发去除，去除后的位置平坦化效果明显。

• The influence of curvature radius of the front surface of cornea on the ablation depth and result for correction of myopia is analysed in detail.

  详细分析了角膜前表面的曲率半径对近视眼消融深度和治疗结果的影响。

• Reducing the number of bends and adopting large curvature radius bends.

  减少弯头数量和采用大曲率半径弯头；

• When curvature radius is larger the results for rectangular and cylindrical coordinate are the same.

  当曲面曲率半径较大时，用柱坐标与直角坐标计算差别很小。

• After unloading and resiling, the curvature radius of CT decreases monotonously along with stretch increasing. As a result, stretch is helpful to reducing resilience.

  在「拉弯」作用的情况下，卸载回弹后的曲率半径随着拉力的增大而单调减小，因此拉力的作用有助于减小回弹。

• The results show that the seismic response of curved beam bridge and the influence of curvature radius can be reduced by using lead rubber bearing.

  结果表明：铅芯橡胶支座不仅可以有效地降低曲线梁桥的地震响应，还有助于减少曲率半径对曲线梁桥地震响应的影响。

• And give out the unified optical path, Newton「s ring radius and convex lens curvature radius measurement formula of non - contact type, simple cutting type and tangent type Newton」s Rring.

  并给出了非接触式、浅近切割式及相切式牛顿环的统一的光程差，牛顿环半径及凸透镜曲率半径测量公式。

• The data transform program has been compiled with MATLAB, which sequentially finishes transformation of part curvature radius into control coordinate of machine tool.

  用MATLAB编写了数据转化程序，完成了变曲率零件从型值点的曲率半径到机床控制坐标的转换。

• Researched friction loss and ultimate strength of external prestressing tendon considering deviator curvature radius and bending angle of prestressing tendon.

  研究了转向块曲率半径、钢绞线弯折角度等对预应力摩擦损失和体外预应力筋极限强度的影响；

• The motion of charged particle acted upon by Lorentz force and other external force are analyzed, calculating formulae of orbit equation and curvature radius are derived.

  分析了带电粒子受到洛伦兹力和其他恒定外力作用下的运动情况，导出了轨道方程和曲率半径的计算公式。

• The differences of stress state between extrusion-flanging and traditional flanging, and the influences of curvature radius of burring punch on flange height were analyzed.

  分析了挤压翻边与传统翻边应力状态的不同之处，以及翻边凸模的沖头曲率半径对翻边效果的影响。

• Medium and small tanks and surface curvature radius of curve or surface smaller irregular equipment, building the air duct insulation and dew and wall body sound-absorbing heat preservation.

  小型储罐及表面曲率半径较小的弧面或表面不规则的设备、建筑空调管道保温防露和墻体的吸音保温。

• Calculation of curvature radius when the outside belt is not away from the rollers.

  按外侧胶带不离开托辊计算曲率半径。

• Little has been presented about the existing small curvature radius U-shaped prestressed tendon, whose practical elongation value and theoretical stretching elongation deviate greatly from each other.

  基于现有规范小曲率半径U形预应力筋张拉伸长量缺乏陈述，而该类预应力筋实测伸长值和理论伸长值偏差过大。