英汉例句

• qualitative and quantitative analysis between deposited metal performances and alloying element factors in flux-cored wires are also discussed.

  并利用所建模型，对堆敷金属性能与因子间的相关性进行了定性和定量分析。

• the microscopic analysis results indicate that deposited metal is hypereutectic structure.

  测试结果表明熔敷金属为过共晶组织。

• when using the aluminium contained steel sheath, the harmf of aluminum to the properties of deposited metal can be limited to some extent.

  采用含铝钢带制造自保护药芯焊丝能充分发挥铝的有利作用，同时减少熔敷金属中残留铝含量及对性能的不利影响。

• the microstructure of the deposited metal and the effect of the welding heat input on the formation of the deposited metal are studied.

  分析了堆焊熔敷金属的显微组织，研究了焊接线能量对堆焊层金属显微组织形成的影响。

• the results indicate that the austenitic transformation temperature of the deposited metal of w110 wire is 692~779 ℃, δ-ferrite exists in 1330~1468 ℃, the solid and liquid phase lines is 1371~1468 ℃.

  结果表明，该焊丝熔敷金属的奥氏体转变温度为692～779 ℃，在1330～1468 ℃温度区间存在高温铁素体相，固液相温度区间为1371～1468 ℃；

• the deposited metal of dkcm50 is single-phase of austenite.

  dkcm50堆焊层金属基本上是单相奥氏体组织。

• welding the utmostly important structure, such as petroleum platform on ocean, pressure containers, etc. the low-temperature impact toughness of deposited metal is extremely strong.

  焊接十分重要的结构，如海洋石油平台、压力容器等，熔敷金属低温性能优异。

• in this paper, using alkanethiol self_assembled monolayers (sams) on gold as model interface, the behavior of deposited metal on sams surface and the interaction mechanism were analyzed.

  本文介绍了金属原子在烷基硫醇自组装单分子膜表面的再沉积行为，从理论上分析了其作用机理，归纳出了金属在自组装单层膜表面的再沉积规律。

• deposited metal fluidity better than 308l, on weld the operation too more superior.

  熔敷金属流动性较308l为佳，在焊接操作上也更优越。

• the deposited metal has excellent mechanical properties. it is used for welding middle-carbon and low-alloy steel structure, such as pressure containers, bridges, and ship structure.

  熔敷金属力学性能优良，用于中碳钢和低合金钢重要结构的焊接，如压力容器、桥梁及船舶结构。

• the alloy elements such as mo, v have distinct effect on the deposited metal grain refinement.

  合金元素钼、钒对堆焊金属晶粒的细化作用效果明显。

• by adding magnesium powder into the coating of electrode, the sulphurs removal in deposited metal was satisfactory.

  通过理论分析及实验，探讨了手工电弧焊焊条药皮中添加金属镁粉的脱硫效果。

• in this paper, the oxidation behavior of deposited metal for new ni-base flux-cored wire in air at the temperature of 800℃ and 1000℃ was studied by using the oxidation weight increasing method.

  采用增重法测定了自制新型镍基药芯焊丝熔敷金属在800℃和1000℃空气中的高温氧化行为。

• deposited metal can meet high welding quality and corrosion resistance.

  熔敷金属能满足较高的焊接质量和耐腐蚀性能。

• the transition coefficients of alloying from cored wire to deposited metal during co2 gmaw have been studied in this paper.

  研究了药芯焊丝在co2保护电弧堆焊过程中合金元素的过渡系数。

• dissolve deposited metal has low hardness and high toughness, heat corrosion resistance to impact abrasion.

  溶敷金属具有低硬度高韧性，可耐热耐腐蚀耐沖击磨耗。

• the results show that cobalt-based dies deposited metal has especially significant impact strengthening under high temperature impact.

  试验结果表明：钴基模具堆焊金属具有较显着的沖击强化效果，尤其是高温沖击强化效果。

• deposited metal of martensite with high hardness, good abrasion resistance, impact resistant performance of hardness hrc55 ~ 58.

  熔敷金属具有高硬度的马氏体组织，耐磨耗耐沖击性能优良，硬度hrc55~58。

• used for welding key structure, such as shipbody structure. the deposited metal has excellent low-temperature impact toughness and crack-resistance.

  用于重要结构的焊接，熔敷金属具有良好的低温沖击韧性和抗裂性能。