英语释义

1. deformation that disappears upon removal of the external forces causing the alteration and the stress associated with it

片语

elastic diameter deformation rate弹性直径变形率

elastic volume deformation弹性体变形

elastic shear deformation弹性剪切形变

elastic large deformation弹性大变形

elastic after deformation弹性后效变形

Elastic Contact Deformation弹性接触变形

elastic solid deformation弹性体变形

elastic rolls deformation轧辊弹性变形

shafting elastic bending deformation轴弹性弯曲变形

英汉例句

• elastic deformation is that part of the deformed material which when the applied load is removed would spring back to its normal shape.

  弹性变形是材料变形部分在去除载荷后可以恢复到原来的形状。

• the micro angle induced by the tooth surface elastic deformation causes the change of meshing points.

  将齿轮因齿面变形而产生微小转角，继而进行齿面啮合分析的过程定义为拟赫兹接触分析。

• the influence of the bite, the entrance and exit elastic deformation and the roller both ends contact pressure is considered . the formula is convenient and precise.

  本公式考虑铝箔入口和出口弹性变形和轧制铝箔两侧轧辊辊身端部弹性接触压力对轧制力的影响。本公式计算精确而且简便。

• through an example, the influence of the elastic deformation and each random parameter on the mechanism reliability of motion function is analyzed.

  通过算例，分析了机构的弹性变形和各随机参数对机构运动功能可靠性的影响。

• for the double-acting accurate gearing trains, the shafting elastic deformation is also one of main factors affecting the return stagnant angle.

  对于双向精密齿轮传动链，轴弹性变形也是影响回差计算的主要因素之一。

• as the material is deformed beyond the strain that elastic deformation persists, the stress is no longer proportional to strain, and permanent, nonrecoverable, or plastic deformation occurs.

  当材料的形变超出弹性形变发生的范围，其应力将不再与应变成正比，永久的、不可回复的形变发生，即为塑性形变。

• so far people pay too much attention to the origin, distribution, structure and elastic deformation of the reticulate red clay.

  至今人们对于网纹红土的研究主要集中在其成因分布、结构构造、弹性变形等方面。

• roll elastic deformation must be considered when plate rolling mill is designed and rebuilt and plate shape is controlled and improved.

  在设计、改造板带轧机，以及控制和改善板形时都要对轧机辊系弹性变形进行考虑。

• during normal operation the couplers are capable of absorbing normal compression loads by elastic deformation only.

  正常运行时，联轴器能够吸收仅有弹性变形产生的正常抗压荷载。

• once again, such as the kinematic model of the pole pieces of the elastic deformation also exists, and ignores the deformation of the truss will also have some error.

  再次，如运动学模型中的桿件的弹性变形也是存在的，忽略了这些桿系的变形也会有一定的误差。

• elastic deformation of the barrel is calculated by means of the preceding n orthonormal modals of the cantilever beam.

  模型中将炮管处理为运动支撑上的悬臂梁，取其前n阶正则模态计算炮管各断面中心的变形和转角。

• elastic deformation occurs at stress below the yield stress, the viscous flow appears after yield with thixotropy.

  验证了在剪切应力低于屈服应力时，变形基本上是弹性的，而屈服后粘流过程显示了触变特性。

• the predicted models of plate crown, the prediction and feedback models of plate shape are set up on the basis of ben cheng's elastic deformation theory by simplifying and discretizing the models.

  以本城轧辊弹性变形理论为基础，通过模型简化和离散化建立了板凸度预报模型、板形预测模型及板形控制反馈修正模型。

• the results showed that the plastic deformation and instant elastic deformation for heavy load stretching were larger than under light load stretching.

  结果表明：较大载荷下肌腱的塑性变形和急弹性变形明显增加；

• as a particular example, dynamic equation both for rigid body and for elastic deformation body can be obtained directly from the universal dynamic equation.

  该方程简化后可得到刚体动力学方程和弹性变形体动力学方程。

• we also analyse the critical velocity, at which elastic deformation translate to plastic deformation when the bullet impact the tube.

  同时也分析了沖头对圆管碰撞时，导致圆管由弹性变形向塑性变形转化学的临界速度值。

• it is believed that the principle of porosity invariance during process of tight rock elastic deformation will provide a good deal of convenience for ooip or reserve estimation.

  致密巖石弹性变形过程中的孔隙度不变性原则将给储量计算带来很大的方便。

• to study the load distribution of hollow roller bearing, the iterative algorithm is adopted based on understanding the construction of the total elastic deformation of roller and raceways.

  为了分析空心圆柱滚子轴承的载荷分布，在分析滚子与内外滚道接触变形量构成的基础上，提出了空心圆柱滚子载荷分布的迭代算法。

• the analysis and calculation indicates that the power loss induced by the elastic deformation of rubber hose can not be ignored.

  通过分析及计算表明：软管的弹性变形所消耗的能量是不容忽视的。

• the mathematic model of elastic deformation of ucm rolling mill has been developed by using influence function method.

  利用影响函数法建立ucm轧机的辊系弹性变形数学模型。

• a unified theory is presented to analyze some conventional methods for estimating the bending rigidity of fabrics, which described the elastic deformation of fabrics under gravity.

  对由自重产生挠曲的各种织物弯曲刚度测定方法给出统一的理论分析。

• the elastic deformation of the i shape simply-supported steel beams with web openings is composed of the deformation of the integrate beam and the additional deformation of the beam with web openings.

  将腹板开孔钢梁的弹性挠曲变形视为完整钢梁的变形和开孔部分梁段附加变形的迭加；

• the indentation process is divided into two ordinal phases: elastic deformation phase and ductile deformation phase.

  在压入过程中，基体的变形可分为两个特征阶段，即初期的弹性变形阶段及后期的塑性变形阶段；

• a method of energy difference between elastic deformation and elastic-recovery deformation is developed to determine the residual deformation energy.

  本文提出用弹性变形能与弹复变形能的差值来确定残留变形能的方法。