片语

high finishing mill四辊精轧机

finishing bar mill棒材精轧机

aluminum foil finishing rolling mill铝箔精轧机

six-high finishing rolling mill六辊精轧机

Finishing rolling mill精轧机

four high finishing rolling mill四辊精轧机

finishing plate mill中厚板精轧

英汉例句

• when finishing mill system vibrated violently, vibration response and operation parameters were measured.

  在精轧机系统发生强烈振动的情况下，对振动响应和运行参数进行了测试。

• the variation of mean flow stress of two kinds of low carbon steel rolled in angang 1780 finishing mill were analyzed.

  本文分析了鞍钢1780生产的两种低碳钢在热连轧过程中平均流变应力的变化。

• guide of finishing mill is the key component of rolling mill. enduring the impact of hot billet, friction, extrusion and cooling of the cooling water, it is often worn and tear badly.

  精轧机入口导板是轧钢机的关键易损零件，在高温下同时承受炽热钢坯的沖击、摩擦和挤压，以及冷却水的激冷，磨损十分严重。

• cooling control system between finishing mill regulates the water-flow with electric signal and compressed-air to control the temperature of the hot strip steel.

  精轧机机架间带钢冷却控制系统，用电气控制信号和压缩空气联合控制冷却水的流量，从而达到热轧带钢温度控制的目的。

• the paper describes the structure, the basic control principle and the control way of the driving system of finishing mill in the high-speed wire rod of tiangang group.

  介绍了天钢集团高速线材厂精轧机传动控制系统的构成、基本控制原理和控制方式。

• caster and finishing mill are directly connected in this process, that's why holding furnace is necessary as a buffer zone against troubles occurred in finishing mill.

  由于铸机和精整是直接相连的，因此保温炉成为精整出现故障后的一个缓沖区。

• the finishing mill f3 repeatedly occurs accidents of rolling crack and stopping steel plate in debugging production stage of thin slab concasting and conrolling production line in bengang.

  本钢薄板坯连铸连轧生产线在调试生产阶段，精轧机f3多次出现轧裂卡钢停产事故。

• the method and example of pass optimization design of high speed wire rod finishing mill by dynamic programming with minimum total tension coefficient are described.

  阐述了以动态规划法按最小总张力系数对高速线材轧机精轧机组孔型进行优化设计的方法与实例。

• the article describes the main drive gear reducer structure at finishing mill area of strip hot continuous rolling plants.

  简要介绍带钢热连轧机精轧区主传动减速机的结构特点。

• diligent, independent, teamwork and can traveling. 1. comprehensive knowledge of seamless, erw tube plant and finishing mill products.

  全面了解钢管包括无缝和焊管的生产线和精整生产线的生产工艺；

• to reduce the weight and cost of finishing mill to the minimum, optimum design computes the important parameters with constrained cyclic coordinate method, and precision is improved further.

  而辊系优化推理部分以降低精轧机重量和减少造价为目的，采用约束坐标轮换法对辊系和机架参数进行优化推理，进一步提高设计精度。

• the control valves arranged over and under the run out tables located between the finishing mill and the down coiler can be controlled through the cool…

  冷却段将控制布置在精轧机与地下卷曲机之间输出辊道上下间的水阀，通过调整这些阀的水量来控制冷却温度和冷却速率。

• it has been proved that high cr cast iron rolls are fit for finishing mill of 1549 hot strip mill of tisco.

  介绍了高铬轧辊化学成分和生产工艺，实际使用证明高铬轧辊适合太钢1549热连轧精轧机组。

• the reclaiming process can be simply carried out on an open mill or finishing mill at the room temperature without any pollution in the production.

  复原胶生产工艺简单，在常温下用开炼机或精炼机即可，而且生产过程中无污染。

• this paper introduces the construction, principle and software functions of plc control system for finishing mill group in high speed wire rod mill at tangshan iron and steelco.

  本文介绍唐钢高速线材轧机精轧机组plc自动控制系统的结构、原理和软件功能。

• the load-commutated inverter(lci) fed synchronous motor control system which is applied to the main drive for high speed wire finishing mill of baotou iron and steel co is presented.

  介绍了用于包钢高速线材厂精轧机主传动中的负载换流同步电动机控制系统。