片语

nominal shortest irradiation time[特医]

long time irradiation长期辐照

zero irradiation solar time零辐照太阳时

accumulative irradiation time累积日照时间

laser irradiation time激光辐照时间

uv irradiation time光照时间

fuel irradiation time燃料辐照时间

microwave irradiation time微波时间

英汉例句

• inactivation of microbes were improved by strengthening power intensity, prolonging irradiation time and increasing temperature.

  超声强度增大、作用时间延长、温度升高都有利于杀菌效果的提高；

• the influences of amount of catalysts, microwave power, microwave irradiation time and the mole ratio of alcohol to acid were studied.

  考察了催化剂的用量、微波功率、微波辐射时间、醇酸比对酯产率的影响。

• the results showed that the mass loss is in proportion to the irradiation time of atomic oxygen.

  结果表明，材料的质量损失与原子氧的作用时间成正比。

• the effects of ultrasonic irradiation power and irradiation time on processing and mechanical properties of hdpe during extrusion were studied.

  研究了在挤出过程中超声辐照功率和时间对高密度聚乙烯（hdpe）加工流变性能及力学性能的影响。

• the results show that if the irradiation time of the pulsed light is much greater than the response time, the incident position of pulsed light satisfies the conversion formula of one-dimensional psd.

  结果表明，如果脉沖光照射时间远远大于psd的响应时间时，光的入射位置满足一维psd的转化公式；

• if irradiation time is too long, the hatching rate would be reduced.

  照射时间过长，孵化率反而降低。

• choosing appropriate laser power and reducing laser irradiation time in laser drilling can also improve drilling quality.

  激光鉆削时，选择合适的激光功率及减少激光照射时间可提高鉆削质量。

• the effects of various acids different in concentration, ratio and irradiation time on the zn content are also investigated.

  并考察了辐射时间、不同配比、不同浓度和不同种类的酸对配合物锌含量的影响。

• this paper discussed the relationship between laser irradiation time and hatching rate of artemia eggs.

  本文讨论了激光照射时间与卤虫卵孵化率之间的关系。

• the effects of microwave power, irradiation time and the purifying way of product on the alkylation were discussed.

  探讨了辐射功率、时间、产物提取方式和卤代烷等对产率的影响。

• the resulting polymer「s molar mass was still very high and polymer yield and monomer conversion increased a little when prolonging irradiation time to a degree at low power.

  在较低的微波功率下适当延长辐照时间，聚合物分子量仍然维持在较高的水平，同时可使聚合物产率和单体转化率有所提高。

• the effects of concentration of n-vp and light sensitive agent dmt in the grafting solutions and irradiation time on the grafting yield in acid and basic mediums were investigated.

  测定了接枝率与接枝液中n-vp单体浓度、光照时间、催化剂浓度等条件的关系。

• the influence of the ratio of two resins, concentration of photoinitiator, and ltv」 irradiation time on the properties of cured film was investigated also.

  本文还系统的考察了树脂在光固化时，两种基体树脂配比的不同、光引发剂用量的变化、光照时间的不同对于涂料固化交联度的影响。

• beyond the scope of a certain period of time, extending the irradiation time of hifu on glioma tissues does not enhance the killing effects of hifu on glioma cells;

  超出一定的时间范围，延长hifu对肿瘤组织的辐照时间，不能增强hifu对肿瘤细胞的杀伤作用；

• the irradiation time decreases with increasing beam current.

  结果表明，提高电子束束流，可缩短辐射硫化时间；

• choosing appropriate laser power and reducing laser irradiation time in laser drilling can also impr…

  激光鉆削时，选择合适的激光功率及减少激光照射时间可提高鉆削质量。

• if irradiation time was invariable, the increment of beam current was not linear with the output of 18f-as a whole.

  轰击时间一定的情况下，总体上束流强度的增加与18f-产量之间无线性关系。

• influences of immersion time of film in the solution of initiator, monomer concentration, reaction temperature and uv irradiation time on grafting effect are studied.

  研究了膜在光引发剂溶液中的浸泡时间、单体溶液的浓度、反应温度和紫外光照射时间等对接枝效果的影响。