英语释义

• joint made by overlapping two ends and joining them together

片语

lap p joint flange活套法兰

lap p joint stud活套环圈

lap p joint搭接头

multiple lap-joint多接缝

halfgauge lap scarf joint半叠楔接

lap-joint sheeting搭接板

half lap scarf joint[建]

lap riveted joint搭铆接合

英汉例句

• it suggested lap joint should be avoided in load carrying structures.

  指出了在承力结构中应该尽量避免搭接焊。

• the single lap joint fails when the crack length reaches to the critical size.

  当裂纹扩展到临界尺寸时，接头会迅速破坏。

• the pin load distribution of scarfed lap joint was studied using abaqus software.

  利用abaqus软件对壁板斜搭接件各钉承载比例进行了三维有限元分析。

• taking the form of lap joint as an example, the effect of final assembling deviation affect by the assembly sequence was analyzed by adopting the method of worse condition.

  以搭接接头形式为例，采用最坏情况法分析了装配顺序对最终装配偏差的影响。

• the bem technique for adhesive-bonded structure proves valid by comparing the stress distribution for double lap joint calculated in this paper with that calculated by finite element method.

  对双搭接接头进行了边界元应力分析，并和有限元结果进行了对比，从而证实本文方法的有效性。

• the test results show that the reinforced porous brick wall similar to normal reinforced brick wall on aseismic design, shear resistance of the bar cannot be used very much when using lap joint …

  试验结果表明，配筋多孔砖墻与配筋普通砖墻具有相近的抗震性能，水平筋采用搭接接头时不能发挥钢筋的抗剪作用以及端部锚固钢筋具有提高承载力和约束砌体作用等。

• what is the maximum size of the fillet welds of a lap joint of member 3/8in. thick ?

  焊件厚度为3/8in的搭接接头的角焊缝的最大尺寸是多少？

• describe the usual problems of lead lap joint about valve electric actuator when working and the improvement of joint process.

  阐述了阀门电动装置运行现场导线搭接的常见问题与搭接工艺的改进。

• the finite element method(fem) is applied to investigate the effect of metal inlay in single lap joint on the stress distribution.

  利用有限元方法研究了金属镶嵌对单搭接接头应力分布的影响。

• the shear strength and elongation of the lap joint increase with the increase of strain rate.

  焊点的剪切强度及伸长量随应变速率的增加而增加。

• for software, it takes use of the swing torch and integral contrast method to realize the seam auto tracking according to the characteristics of lap joint tig welding;

  软件处理方面，针对搭接tig焊的特点，采用摆动焊接方法，利用积分比较法，实现了焊缝的自动跟蹤；

• the results indicate that good lap joint between aluminum and galvanized steel sheet can be made in appropriate parameters.

  试验结果表明，铝和镀锌钢能得到成形良好的搭接接头。

• the effect of elastic modulus of adhesive on the str ess distribution in aluminium alloy single lap joint was investigated using elastic-plastic finite element method(fem).

  运用弹塑性有限元法，研究了胶粘剂弹性模量对含间隙的铝合金单搭接接头上应力分布的影响。

• the waterproof layer of the lap joint should stick (welding) firm, tight sealing, no distortion, fold, curling and blister defects.

  卷材屋顶防水层的搭接缝应粘（焊）结牢固，密封精密，不得有扭曲、皱折、翘边和起泡等缺陷。