英语释义

1. a curve usually on a temperature-composition diagram for a binary system that over a range of temperatures between the melting points of the pure components relates compositions of the liquid phase to the solid phase in equilibrium with the liquid phase and that indicates temperatures above which only the liquid phase can exist — compare solidus, solvus

片语

styrax liquidus翻译

aquiform水状的；液体的

liquid line液体管线；液线；[热] 液相线

liquidus curve液相曲线

fluent流畅的，流利的；液态的；畅流的

liquidus litharge密陀僧

liquidus point液相点

nearby liquidus近液相线

liquidus surface液相面

liquidus line液相线

liquidus s液相线

liquidus temperature液线温度

英汉例句

• solidus and liquidus temperatures of the rocks and relationship between crystallinity and crystallization temperature have been determined.

  确定了巖石固相线与液相线的温度，巖石结晶程度与温度的关系。

• the dsc results indicate that above the liquidus temperature, the zl114a alloy melts structure varies with the increase of temperature.

  综合热分析dsc结果表明：在液相线以上，zl114a合金熔体的结构状态随温度发生变化。

• the casting and remelted microstructures of zl201 alloy cast by liquidus semi-continuous casting(lsc)were studied.

  研究了近液相线半连续铸造zl201合金的微观组织及其在二次加热过程中的变化。

• besides the cell voltage, bath temperature and bath ratio, the inputs of the system also include the liquidus temperature, superheat extent and cathode voltage.

  系统的输入参数除传统的电压、温度和分子比外，还采用初晶温度、过热度和阴极压降等作为系统的输入参数。

• they and the steel wire and solid-phase liquidus temperature and the size of the crystallization temperature range.

  它们与钢的固相线和液相线温度的高低及结晶温度区间的大小有关。

• low liquidus temperature enables low bath temperature. the current efficiency increases with the decreasing of bath temperature.

  低液相线温度允许低电解温度，而降低电解温度可大大提高电流效率。

• during the melting and processing practices, an accurate knowledge of liquidus temperature is necessary in the determination of process parameters relating to a given alloy.

  在合金熔炼和加工过程中，往往需要知道液相线温度，以便确定相关工艺参数。

• with the steel line and the solid phase of the high and low liquidus temperature and crystallization temperature of the size of interval.

  它们与钢的固相线和液相线温度的高低及结晶温度区间的大小有关。

• the simulated process of solidification also shows some results as follows: 1 there is no direct relationship between the distribution of solid fraction and of liquidus .

  通过凝固过程模拟分析还得出了以下主要结果：1）凝固过程中的固相分数分布与液相线分布之间没有确定的直接联系。

• the adiabatic heating induces the temperature of fracture surface layer to be higher than the liquidus temperature too.

  计算表明，断口表面层绝热升温温度依然高于液相线温度。

• the liquidus temperatures determined by petrographic microscopy method are in better aggreement with those determined semiquantitatively by the extrapolation method of x-ray diffraction intensity.

  液相温度用偏光显微镜和半定量x射线衍射强度外推法两种方法来确定，并且这两种方法测出的结果比较接近。

• the solid/liquid phase transformation of zl201 aluminium alloy in near liquidus semi-continuous casting was simulated using multiscale simulation technique.

  用多尺度模拟方法研究了近液相线半连续铸造中的zl201合金的液/固相变。

• the glass has a melting temperature less than about 1650 deg c. and a liquidus viscosity of at least 130 kpoise and, in one embodiment, greater than 250 kpoise.

  该玻璃的熔融温 度小于约1650℃，液相线粘度至少为130千泊，在一种实施方式中，大于250千 泊。

• liquidus temperature of actual aluminum electrolyte samples was measured directly.

  直接测定了铝电解质实际样品的初晶温度。

• the microstructure evolution of zl111 by heat holding above the liquidus temperatures was investigated.

  对zl111铝合金在近液相线的温度保温后的铸态组织进行了研究。

• the compositions can be designed using theoretical calculations of the liquidus temperature to have substantial amounts of refractory metals, while still maintaining a depressed liquidus temperature.

  所述组成可以使用液相线温度的理论计算进 行设计以便包含大量的难熔金属，并仍然保持低的液相线温度。

• studying the nearby liquidus semi -continuous casting technics of a356alloy by means of orthogonal test.

  选用正交试验法，研究了a356铝合金近液相线半连续铸造工艺参数的影响。

• metal is preheated in a furnace or crucible until is above the liquidus temperature in a suitable range (we don't want the metal solidifying before the pour is complete).

  金属在熔炉或坩埚中预热到高于液化温度的一个合适范围内（不希望金属在浇铸完成前凝固）。

• the results showed that compression stress in semi-solid state for liquidus and conventional cast alloy 2618 and 7075 was lower than that in solid state.

  研究了铝合金2618、7075的液相线铸造组织和常规铸造组织在不同变形温度和变形速率下压缩变形的基本力学特征。

• in the liquidus nearby , the grains size becomes coarse with increasing of casting temperature.

  在液相线附近，晶粒尺寸随着浇铸温度的降低而逐渐减小并呈球化的趋势。

• so a method to measure the surface tension at liquidus temperature was proposed.

  基于此，提出了一种测量液相线温度下表面张力的方法。

• the kinetic solidus and liquidus approach to t0 curve with increasing growth velocity on two different isopleths of the alloys.

  在合金两个不同等深面上，界面移动速度增加时，固相线和液相线向同素异型相界t0曲线靠近；

• the results show that: manganese lowers liquidus and eutectic temperature, and narrows down the temperature range of solidification;

  结果表明：锰降低液相线温度和共晶温度，缩小凝固温度范围；

• semi-solid slurry of y112 alloy was cast by near liquidus semi-continuous (nlsc).

  采用近液相线半连续多模铸造法制备出y112铝合金半固态坯料。

• it was found that the simulated grain size and morphology of near liquidus cast zl201 alloy is well consistent with experimental results.

  对zl201合金的近液相线铸造组织的模拟结果与实验吻合。

• using resistance furnace, the structure of a356 aluminum alloy casted by nearby liquidus semi-continuous was studied during remelting by means of electron microscope and image analysis apparatus.

  利用电阻炉加热，采用电子显微镜及图象分析仪，研究了近液相线铸造a356铝合金在二次加热过程中的组织变化。

• the engendering rule of organism of liquidus casting aluminum alloy a356 at different heat preservation temperature, different heat preservation time was investigated.

  研究了液相线铸造a35 6铝合金在不同保温温度、不同保温时间下的组织形成规律。