片语

Standard printing plate thickness标準印刷版厚度

Plate Making Thickness工作人数

Plate thickness measurements钢板厚度测量

plate e thickness筛板厚度

Plate of moderate thickness[材]

Plate by Thickness不锈钢箔

Plate thickness clear deviation插片厚度明显偏差

max steel plate thickness焊接钢板最大厚度

英汉例句

• This paper introduces a neoteric metal plate thickness detector using two-capacitor sensor, based on traditional metal plate thickness detector using parallel capacitor sensor.

  本文在研究了传统的并联式电容传感器金属板带测厚仪的基础上，提出了一种新型的独立双电容传感器金属板带测厚仪。

• A design model of a finite length rectangular pressure vessel was established based on the plate heap theory, the calculation formula of the side plate thickness was derived.

  在平板叠加理论的基础上，建立了一个有限长对称矩形压力容器的设计模型，并推导出其侧板厚度的计算公式。

• The position of minimum values on the sound transmission loss curve varies with the changes made on plate thickness and the moment of inertia of stiffeners.

  板厚或肋骨惯性矩的变化会引起结构传声损失曲线上隔声低谷位置的变化；

• The attention was focused on the effects of the aperture size, the cavity depth and the perforated plate thickness on the impedance of the liner.

  着重于声衬的孔径、腔深、孔板厚度对声衬性能的影响。

• The plastic zone size of the crack tip is relative to three dimensional constraint which depends upon not only the plate thickness but also the load and the material property.

  裂纹尖端塑性区的大小与其三维约束状态有关，而三维约束状态不仅与板厚还与外载荷、材料性质有关。

• When the plate thickness approaches to the limit of thin plates, the current element degenerates to the thin plate element automatically, so that the shear locking phenomenon will not appear.

  在薄板极限情况下，这种厚薄板通用单元自动退化为原来的薄板单元，消除了剪切闭锁现象。

• The first step, because the river entities seeper, milling equipments must float on water work, need USES the steel plate made floating bodies, plate thickness of 3.5-4 mm.

  第一步，因为河道里存有积水，选矿设备必须要浮在水面上工作，需要用钢板做成浮体，钢板厚度为3.5 -4毫米。

• At the same time, it presents the effects of concrete code and plate thickness on fatigue property of plated RCbeams.

  同时，还探讨了混凝土强度、补强钢板厚度等因素对粘钢补强梁的疲劳性能影响。

• The calculation for the tube plate thickness of heat exchanger is complex in normal design.

  而在换热器设计过程中，管板厚度设计计算比较复杂。

• At first, it is verified that the formerly obtained formula for calculating base plate thickness of stilling basin is in good agreement with engineering practices.

  根据前期研究得出的消力池底板厚度公式，经工程实践验证，符合程度良好。

• The influences of the finite plate thickness and the orifice shape are also taken into account.

  模型中还考虑了实际应用中经常遇到的小孔形状和穿孔板厚度两个重要因素。

• To lead anode plate thickness uniformity, we proposed the dynamic lost heavy method realization lead anode plate casting method. It increased the precision of casting the lead anode plate.

  为使铅阳极板厚薄均匀，提出了动态失重法实现铅阳极板定量浇铸的方法，提高了铅阳极板的浇铸精度。

• Moreover, the high phosphorus diets appeared the tendency of epiphyseal plate thickness and bone cortical thickness decreasing.

  高磷日粮呈现降低生长板和骨皮质厚度的趋势。

• In consideration of melt pressure, the circular plate thickness can be calculated in accordance with the formula.

  考虑熔体压力，圆形板厚度可由公式算出。

• The equivalent plate thickness method can be used in choosing type and rough calculating in primary design. The nonlinear contact method can be used in final calculating and guiding model test.

  等效板厚法可用于初步设计时选型、初算，而非线性接触方法可用于最终计算及指导模型试验。

• This paper discusses how the weld groove and the plate thickness affect the sheet metal manufacture processing, and how to design with reasonable method.

  本文阐述了焊接坡口和板厚处理对钣金加工制造工艺的影响，并用合理的方式设计和处理。