片语

Cooling of polymer melt聚合物熔体的冷却

polymer melt intercalation插层法

polymer melt fracture高分子熔体破裂

viscoelastic polymer melt黏弹聚合物熔体

skin polymer melt forming表层聚合物熔体形成

polymer melt temperature聚合物熔化温度

polymer-melt directly spinning熔体直纺

英汉例句

• During Exerusion, the polymer melt flow in cone dies was discussed in this paper.

  本文讨论了聚合物熔体在圆锥口型中的流动问题。

• The methods used to analyze polymer melt flow in extrusion dies are reviewed.

  综述挤出口模中聚合物熔体流动分析方法。

• Advances in the viscoelastic behavior of polymer melt both home and abroad have been reviewed.

  综述了国内外对聚合物熔体粘弹行为的研究。

• The equivalent distance method is put forward to determine polymer melt front advancement during injection molding.

  提出一种新的确定注塑成型充模阶段塑料熔体前沿位置的当量距离法；

• The innovation scheme for filtration of polymer melt was presented, including spinning pack, polymer melt filter and improvement of TiO2 filter.

  介绍了有关熔体过滤方面的改造方案，包括纺丝组件、熔体过滤器和二氧化钛过滤器的改进。

• The design of the coat-hanger die is of significant importance for the polymer melt distribution across the die and the quality of the final product.

  衣架型模头的设计对于熔体分配的均匀性乃至最终产品的均匀性至关重要。

• The response of the polymer melt behavior of orientation for axial vibration of screw in short pipe extrusion die head was studied by the light scattering technology.

  利用光散射测量方法研究了短圆管挤出模头中聚合物熔体取向行为对螺桿轴向振动的响应。

• Gas assisted plastics injection molding process includes injection of polymer melt into mold cavity and then injection of gas-compressed into the polymer melt.

  气体辅助注塑成型工艺包含塑料熔体注射和气体注射两部分，由气体推致力塑料熔体充满模具型腔。

• The applications of polymer melt gear pump in plastics extrusion and microcellular plastics forming are introduced.

  介绍了熔体齿轮泵在塑料挤出成型及微孔塑料加工中的应用。

• The quoted MFR value is the weight of polymer melt flowing through an orifice in specified conditions, so the higher the MFR value, the lower the melt viscosity and the easier the material will flow.

  MF R采用的数值是在一定的条件下通过口模的聚合物熔体的重量，所以MF R越大，熔体粘度越低，而材料的流动性就越好。

• A special apparatus was constructed by modifying capillary rheometer to study polymer melt flow behavior through fiber beds.

  通过改装毛细管流变仪建立了专门的实验装置，研究高温高压下熔体在纤维床层中的流动行为。

• This paper depicts the principle of polymer melt movement and gas penetration in the gas-assisted injection molding and analyzes the boundary condition of gasmelt interface.

  本文描述了气体辅助注射成型过程中熔体流动和气体穿透的原理，分析了气体和熔体交界处应满足的边界条件。

• Recent research on energy consumption and morphology evolution during the initial stage of polymer melt compounding is reviewed.

  综述了关于高聚物在熔融混合过程中能量消耗及初始阶段形态演化的研究现状。

• Based on the analyses of wall slip mechanism of polymer melt flowing, the effects of wall slip on melt filling flow behavior in micro injection molding were investigated.

  分析了微尺度下熔体壁面滑移机理，研究了微注塑成形中壁面滑移对熔体充模流动行为的影响。

• Moreover, by using a new kind of processing technology-the electro magnetic dynamic extrusion technology, the polymer melt strength can be reinforced.

  同时提出了一种新型的加工技术，电磁动态挤出成型技术可以有效地提高聚合物熔体的强度。

• Coat-hanger die is usually used as the polymer melt distributor of the melt-blown nonwoven system.

  熔喷非织造设备中聚合物熔体分配流道主要采用衣架型模头。

• This paper sums the study results on wall slip of polymer melt in shear flow, which leads to the physical meaning of the developed Z-W model.

  总结了聚合物熔体在剪切流场壁面滑移研究的成果，提出了ZW模型的物理概念。

• Approaches for the fluorination of aromatic polymers can involve a polymer melt that is contacted with an appropriate fluorination reagent.

  氟化芳香族聚合物的方法包括与合适的氟化反应物接触的聚合物熔体。

• The oscillation shear heat generated by polymer melt and cooling stage of polymer in the cavity during the oscillating injection molding are researched.

  研究了振动注射成型中模腔内聚合物熔体产生的振动剪切热，并研究在振动作用下模腔内物料的冷却过程。